null Skip to main content

Economical 6 Foot SnoBar and ColorBar Snow Rail Kits

See Now

Snow Guard for AMS Architectural Metal Solutions

Snow guards for AMS (Architectural Metal Solutions) standing seam roofing panels help manage rooftop snow and ice above walkways, entrances, parking areas, landscaping, equipment, and other places where a sudden release could create property damage or safety concerns. Selecting the correct SnoBlox-Snojax product begins with identifying the exact AMS panel profile and then matching it to a compatible attachment method.

Compatible AMS snow retention options include adhesive-mounted polycarbonate guards, non-penetrating SnoBar and ColorBar rail assemblies, RCB-3 systems, 2-bar systems, and clamp-on SnoCleat products for the Snap Lock, Pro Lock, and Armor Lock profiles.
  • AMS Snap Lock, Pro Lock, and Armor Lock are concealed-fastener standing seam roof panels.
  • These profiles are compatible with the adhesive-mounted polycarbonate guards and clamp-on systems shown in the chart below.
  • EcoJax is a polycarbonate snow guard and fits the same AMS profiles as SnoBlox Deuce.
  • Do not penetrate these panels with screw-down snow guards or screw-fastened rail systems.
  • Final system selection should consider roof slope, panel width, run length, snow load, roofing material, surface configuration, and the complete roof layout.
Important: Do not select a snow guard based on appearance alone. Confirm the exact AMS profile, attachment method, and project requirements before ordering. Clamp-on components must fit the seam correctly, while adhesive-mounted guards require a suitable flat bonding area and proper adhesive application. An incorrect product or layout can reduce system performance or cause premature failure.

⚡ AMS Primary Quick Selection Guide

Use this section for fast profile-level guidance. Confirm product fit in the complete compatibility chart below.

  • Snap Lock Panel: Compatible with the listed adhesive-mounted polycarbonate guards, standing seam rail systems, RCB-3 systems, 2-bar systems, and SnoCleat RC/RCT.
  • Pro Lock Panel: Accepts the same broad selection of adhesive-mounted guards and non-penetrating clamp-on snow retention systems.
  • Armor Lock Panel: Compatible with the products shown in the chart when the panel material and mounting surface are suitable, subject to seam verification and project-specific layout requirements.
  • Standing seam warning: Do not install screw-down snow guards through concealed-fastener AMS panels.

About AMS (Architectural Metal Solutions) Roofing Systems

Architectural Metal Solutions, commonly called AMS, supplies architectural roofing, siding, soffit, and exterior-envelope materials for residential, commercial, industrial, and institutional construction. Its standing seam roofing lineup includes the Snap Lock, Pro Lock, and Armor Lock profiles, each designed with concealed clips that accommodate thermal movement while maintaining a clean finished appearance.

Snow Retention Solutions for AMS Standing Seam Roofing

AMS standing seam panels can use non-penetrating clamp-on snow retention systems when the clamp properly matches the seam, or adhesive-mounted polycarbonate guards when the panel pan provides adequate flat bonding space. TThe three profiles covered here are compatible with the products listed in the chart when the panel material, seam configuration, mounting surface, and attachment requirements are suitable. Always verify clamp fit and adhesive compatibility before ordering.

See our full range of snow guards for metal roofs and use the chart below to review compatible SnoBlox-Snojax products for each AMS profile. 'YES' indicates the product is compatible with that panel.

Snow Guards for AMS Standing Seam Roof Panels

The AMS Snap Lock panel has a 1.75-inch rib and is available in widths from 12 to 24 inches. Pro Lock uses a 1.5-inch rib and is available in widths from 12 to 24 inches. Armor Lock has a 2-inch mechanically seamed leg intended for demanding, low-slope applications. All three profiles can support the adhesive-mounted guards and compatible clamp-on systems shown below.

Standing seam warning: Do not install screw-down snow guards through concealed-fastener standing seam panels. Use compatible seam-mounted products or adhesive-mounted guards where sufficient flat bonding space is available.

Do you need more information about compatible snow guards for AMS standing seam roof panels? Read our full guide here: Snow Guards for AMS (Architectural Metal Solutions) Standing Seam Metal Roof Panels.

  Snap Lock Profile Pro Lock Profile Armor Lock Profile
IceJax I
IceJax I 		YES YES YES
IceJax II
IceJax II 		YES YES YES
EcoJax
EcoJax 		YES YES YES
SnoBlox Deuce
SnoBlox Deuce 		YES YES YES
SnoBlox Ace
SnoBlox Ace 		YES YES YES
SnoJax II
SnoJax II 		YES YES YES
SnowBreaker
SnowBreaker 		YES YES YES
SnoBar Standing Seam
SnoBar Standing Seam 		YES YES YES
ColorBar Standing Seam
ColorBar Standing Seam 		YES YES YES
SnoBar RCB-3
SnoBar RCB-3 		YES YES YES
ColorBar RCB-3
ColorBar RCB-3 		YES YES YES
2 Bar SnoBar
2 Bar SnoBar 		YES YES YES
2 Bar ColorBar
2 Bar ColorBar 		YES YES YES
SnoCleat RC
SnoCleat RC 		YES YES YES
SnoCleat RCT
SnoCleat RCT 		YES YES YES

Snap Lock, Pro Lock, and Armor Lock offer broad compatibility with adhesive-mounted polycarbonate guards and non-penetrating clamp-on snow retention systems.

Before ordering a clamp-on system, test-fit the clamp on the actual seam. Aluminum and copper panels are generally less rigid than steel panels, so a project may require additional rows of a clamp-on rail system. IceStopper attachments are recommended over pedestrian and parking areas when using a rail system.

AMS Snow Guard Buying Checklist

  • Confirm the exact AMS panel name before selecting a snow retention product.
  • Verify the seam geometry and material for Snap Lock, Pro Lock, or Armor Lock.
  • Choose a compatible non-penetrating solution: adhesive-mounted guard, standing seam clamp, RCB-3 clamp, 2-bar clamp system, or clamp-on SnoCleat.
  • Check ground snow load. Individual adhesive-mounted guards are generally best suited to lighter snow-load applications. Higher loads often require professionally designed rail-system layouts.
  • Request a layout rather than protecting only isolated areas such as doors, chimneys, or HVAC equipment.
  • Order samples or individual components when a clamp or guard test fit is needed. SnoBlox-Snojax products are available with no minimum order requirement.

Need Help Identifying Your AMS (Architectural Metal Solutions) Panel?

If you are not sure which AMS (Architectural Metal Solutions) panel you have, carefully compare the panel profile, review the detailed AMS (Architectural Metal Solutions) blog post linked above, and order a single test-fit unit before committing to a full project. For project-specific help, contact SnoBlox-Snojax at support@snojax.com or call 1-800-766-5291.

Do you have a metal roof from a different manufacturer?

Visit our 'Snow Guard Compatibility by Roof Manufacturer' resource page for detailed information on which snow guards and snow retention systems are compatible with your metal roof.

Compatibility Guidance Note

SnoBlox-Snojax bases the compatibility information presented in this guide on product testing and field experience with AMS (Architectural Metal Solutions) metal roof panel profiles. Panel manufacturers periodically update profile specifications, and individual project variables, such as seam condition, coating type, and installation method, can affect outcomes. Customers are encouraged to confirm current panel specifications directly with AMS (Architectural Metal Solutions) and to contact SnoBlox-Snojax with project-specific questions before ordering.

Snow Guards for AMS (Architectural Metal Solutions) Steel Roofing Panels – Compatibility & Installation FAQ

AMS Snap Lock, Pro Lock, and Armor Lock panels are compatible with several adhesive-mounted polycarbonate snow guards and non-penetrating clamp-on snow retention systems. Compatible options include EcoJax, SnoBlox Deuce, IceJax I, IceJax II, SnoBlox Ace, SnoJax II, SnowBreaker, SnoBar, ColorBar, RCB-3 systems, 2-bar systems, SnoCleat RC, and SnoCleat RCT.
This guide covers the AMS Snap Lock, Pro Lock, and Armor Lock standing seam metal roof panels.
Yes. EcoJax is an adhesive-mounted polycarbonate snow guard that fits the same AMS Snap Lock, Pro Lock, and Armor Lock panel profiles as SnoBlox Deuce. The panel must provide enough flat mounting space for proper adhesive installation.
Yes. SnoBlox Deuce is compatible with the AMS Snap Lock, Pro Lock, and Armor Lock profiles when installed as an adhesive-mounted snow guard on a suitable flat bonding surface.
No. Screw-down snow guards and screw-fastened rail systems should not penetrate concealed-fastener standing seam panels. AMS standing seam roofs should use compatible clamp-on systems or adhesive-mounted snow guards.
Compatible options include SnoBar and ColorBar standing seam systems, SnoBar and ColorBar RCB-3 systems, SnoBar and ColorBar 2-bar systems, SnoCleat RC, and SnoCleat RCT. Always test-fit the clamp on the actual roof seam before ordering a complete system.
Yes. Confirm the panel name, seam height, seam shape, panel material, and available flat mounting area before selecting a product. AMS has several standing seam profiles, and actual field conditions can affect compatibility.
You may use adhesive-mounted polycarbonate guards on compatible painted metal surfaces with adequate flat mounting space. Do not install them on copper roofing. Always confirm surface compatibility and follow the SureBond SB-190 preparation and curing instructions.
SureBond SB-190 requires about 28 days at temperatures of 50°F or higher to fully cure. Schedule installation when suitable temperatures can be maintained throughout the curing period.
They may be. Aluminum and copper panels are generally less rigid than steel panels so that a project may require additional rows of a clamp-on rail system. Copper roofs should not use adhesive-mounted polycarbonate guards.
No. Installing snow guards only in isolated areas can concentrate snow loads and place excessive stress on the roof or retention system. Snow guards should be arranged in a complete layout designed for the entire roof area requiring protection.
A proper layout considers the exact AMS panel profile, roof dimensions, panel width, roof slope, eave-to-ridge distance, roofing material, ground snow load, seam configuration, and areas below the roof that require protection.
IceStopper attachments are recommended with SnoBar and ColorBar systems above pedestrian areas, parking spaces, entrances, and other locations where smaller pieces of snow or ice could pass beneath the rail.
Compare the seam shape and panel dimensions with the Snap Lock, Pro Lock, and Armor Lock profiles shown in the AMS standing seam blog. If you're still unsure, order a single guard or clamp for test fitting before purchasing a complete system.
Yes. Contact SnoBlox-Snojax at [support@snojax.com](mailto:support@snojax.com) or 1-800-766-5291 for product selection and project layout assistance. Providing roof measurements, photographs, panel information, roof slope, and the project location will help the team evaluate the application.

!