null Skip to main content

Economical 6 Foot SnoBar and ColorBar Snow Rail Kits

See Now

Snow Guards for Bruce & Dana

Snow guards for Bruce & Dana roofing panels help manage rooftop snow and ice by reducing the chance of an uncontrolled release above entrances, walkways, parking areas, landscaping, equipment, and other vulnerable locations. Because Bruce & Dana manufactures a concealed-fastener standing seam panel, the correct SnoBlox-Snojax solution must suit the panel pan and Snap Lock seam without penetrating the floating roof system.

Compatible Bruce & Dana snow retention options include adhesive-mounted polycarbonate snow guards, non-penetrating SnoBar and ColorBar rail assemblies, RCB-3 systems, 2-bar rail systems, and clamp-on SnoCleat products for the 12-inch Snap Lock panel.
  • Bruce & Dana offers a 12-inch Snap Lock concealed-fastener standing seam roof panel.
  • Compatible adhesive-mounted polycarbonate guards attach to the flat panel surface without roof penetrations.
  • Compatible clamp-on snow retention systems secure to the standing seam and preserve the panel's concealed-fastener design.
  • EcoJax is a polycarbonate snow guard and fits the same Bruce & Dana Snap Lock panel as SnoBlox Deuce.
  • Final system selection should consider roof slope, eave length, rafter length, panel width, roofing material, ground snow load, and the requirements of a complete roof layout.
Important: Do not select a snow guard solely by appearance. Bruce & Dana's Snap Lock roof is a floating, concealed-fastener system, so do not fasten screw-down snow guards and rails through the panel. Choose a compatible adhesive-mounted guard or a non-penetrating clamp-on system. An unsuitable attachment can interfere with panel movement, create leak paths, reduce holding strength, or contribute to premature failure.

⚡ Bruce & Dana Primary Quick Selection Guide

Use this summary for quick profile-level guidance, then confirm the specific product in the complete compatibility chart below.

  • 12-inch Snap Lock panel: Compatible with adhesive-mounted polycarbonate snow guards, SnoBar and ColorBar standing seam rails, RCB-3 systems, 2-bar rail systems, and SnoCleat RC/RCT.
  • EcoJax compatibility: EcoJax fits the same Snap Lock profile as SnoBlox Deuce and is shown immediately above it in the chart.
  • Attachment warning: Do not install screw-down snow guards through this concealed-fastener standing seam panel.
  • Copper consideration: Adhesive-mounted polycarbonate guards are not recommended for copper roofing. Copper panels may also require additional rail rows because copper is less rigid than steel.

About Bruce & Dana Roofing Systems

Bruce & Dana Wholesale Inc. is a locally owned, family-operated supplier of metal roofing and construction materials based in Salem, Oregon. The company has served customers along the West Coast since 1964. It continues under the ownership of Jennifer Helms-Johnson and Joseph Johnson. Its roofing selection includes a 12-inch Snap Lock standing seam panel for residential and commercial applications.

Snow Retention Solutions for Bruce & Dana Roofing

Bruce & Dana's Snap Lock panel uses concealed fastening and is designed to move with thermal expansion and contraction. Snow retention should therefore attach without screws penetrating the panel. Compatible choices include adhesive-mounted polycarbonate snow guards placed on a suitable flat bonding surface and clamp-on products that secure directly to the seam.

Explore our full selection of snow guards for metal roofs and use the chart below to verify SnoBlox-Snojax product compatibility with the Bruce & Dana Snap Lock panel. A "YES" indicates the product is compatible with this profile.

Snow Guards for Bruce & Dana Standing Seam Roof Panels

Bruce & Dana's standing seam offering is a 12-inch-wide Snap Lock panel with a 1-inch-tall seam. The panel is produced in 24-gauge G-90 galvanized steel with a PVDF finish. It can be installed over plywood decking or supported by wood or metal purlins. A 16-ounce copper version is also available by special order.

Standing seam warning: Do not install screw-down snow guards through concealed-fastener standing seam panels. Use a compatible clamp-on system when the seam accepts the clamp, or an adhesive-mounted guard when the panel has an appropriate flat bonding area.

Would you like more detail about compatible snow guards for Bruce & Dana standing seam roofing? Read our complete guide: Snow Guards for Bruce & Dana Wholesale Inc. Standing Seam Metal Roof Panels.

The Bruce & Dana 12-inch Snap Lock profile supports a broad range of adhesive-mounted polycarbonate guards and compatible non-penetrating clamp-on snow retention systems.

Test-fit a clamp sample before purchasing a complete clamp-on system. When a rail system protects pedestrian or parking areas, IceStopper attachments can help retain snow and ice beneath the rail.

Bruce & Dana Snow Guard Buying Checklist

  • Confirm the Bruce & Dana panel name before choosing a snow retention product.
  • Verify the roof material: 24-gauge galvanized steel and special-order copper can require different layout considerations.
  • Choose the correct attachment method: adhesive-mounted or non-penetrating clamp-on.
  • Check the ground snow load. Individual adhesive-mounted guards are generally better suited to lighter snow-load applications. Heavier loads often call for rail systems.
  • Request a layout instead of placing snow guards only above isolated locations such as doors, chimneys, or HVAC equipment.
  • Order a sample or single unit when a test fit is appropriate. SnoBlox-Snojax products and components are available without a minimum-order requirement.

Need Help Identifying Your Bruce & Dana Panel?

If you are not sure which Bruce & Dana panel you have, carefully compare the panel profile, review the detailed Bruce & Dana standing seam roofing guide linked above, and order a single test-fit unit before committing to a full project. For project-specific help, contact SnoBlox-Snojax at support@snojax.com or call 1-800-766-5291.

Do you have a metal roof from a different manufacturer?

Visit our "Snow Guard Compatibility by Roof Manufacturer" resource page for detailed information on which snow guards and snow retention systems are compatible with your metal roof.

Compatibility Guidance Note

SnoBlox-Snojax bases the compatibility information presented in this guide on product testing and field experience with Bruce & Dana metal roof panel profiles. Panel manufacturers periodically update profile specifications, and individual project variables, such as seam condition, coating type, and installation method, can affect outcomes. Customers are encouraged to confirm current panel specifications directly with Bruce & Dana and to contact SnoBlox-Snojax with project-specific questions before ordering.

Snow Guards for Bruce & Dana Steel Roofing Panels – Compatibility & Installation FAQ

Bruce & Dana’s 12-inch Snap Lock standing seam panel is compatible with selected adhesive-mounted polycarbonate snow guards and non-penetrating clamp-on systems. Compatible products include IceJax I, IceJax II, EcoJax, SnoBlox Deuce, SnoBlox Ace, SnoJax II, SnowBreaker, SnoCleat RC, SnoCleat RCT, and several SnoBar and ColorBar rail systems.
Yes. Compatible SnoCleat, SnoBar, and ColorBar systems clamp directly to the Snap Lock seam without penetrating the roof panel. Always test-fit a clamp sample before ordering a complete system.
No. Screw-down snow guards and rails should not penetrate Bruce & Dana’s concealed-fastener Snap Lock panel. Roof penetrations can interfere with panel movement, create potential leak paths, and affect the roof’s performance.
Yes. Bruce & Dana’s Snap Lock panel has flat areas that can accept compatible adhesive-mounted polycarbonate snow guards. Options include IceJax I, IceJax II, EcoJax, SnoBlox Deuce, SnoBlox Ace, SnoJax II, and SnowBreaker. Adhesive-mounted polycarbonate guards are not recommended for copper roofing.
Yes. EcoJax is a polycarbonate snow guard that fits the same Bruce & Dana Snap Lock panel as SnoBlox Deuce. It can be adhesive-mounted to a suitable flat area of a compatible steel panel.
No. Installing snow guards only in isolated areas can concentrate snow loads and place excessive stress on the roof or retention system. A complete layout should distribute snow retention across the entire roof area.
Continuous SnoBar or ColorBar rail systems are generally preferred for higher ground snow loads and longer roof runs. Individual adhesive-mounted snow guards are typically better suited to lighter snow-load applications. A full project layout is still required before ordering or installing any system.
Bruce & Dana’s Snap Lock panel has a 12-inch coverage width and a 1-inch-tall standing seam. Compare the installed panel with the manufacturer’s profile information and measure the panel width and seam height before selecting a snow retention product.
The Bruce & Dana Snap Lock panel is a concealed-fastener standing seam system manufactured in 24-gauge G-90 galvanized steel with a PVDF finish. A special-order 16-ounce copper version is also available. Copper panels may require additional rail rows because copper is less rigid than steel.
Yes. SnoBlox-Snojax has no minimum-order requirement, so customers can purchase an individual snow guard, clamp, or component for test fitting. Confirming compatibility before ordering a complete system can help prevent installation problems.

!