null Skip to main content

Economical 6 Foot SnoBar and ColorBar Snow Rail Kits

See Now

Snow Guards for Dean Steel Buildings

Snow guards for Dean Steel Buildings roofing panels help manage the sudden movement of rooftop snow and ice above entrances, sidewalks, parking areas, equipment, landscaping, and other vulnerable locations. The appropriate SnoBlox-Snojax solution depends on the exact Dean Steel Buildings standing seam profile, its seam geometry, available bonding area, roof material, and project conditions.

Compatible Dean Steel Buildings snow retention options may include adhesive-mounted polycarbonate guards, non-penetrating clamp-on SnoBar and ColorBar systems, RCB-3 rails, 2-bar rail assemblies, and SnoCleat RC or RCT products, depending on the roof profile and project requirements.
  • Dean Steel Buildings Pro Seam, Pro Lok, and Pro-VR are concealed-fastener standing seam roof panels.
  • These profiles are broadly compatible with adhesive-mounted polycarbonate snow guards and compatible non-penetrating clamp-on systems.
  • Never install screw-down snow guards or rails through a standing seam panel.
  • We recommend a test fit before ordering clamp-on products because seam dimensions and field conditions can affect fit.
  • Final system selection should consider roof slope, panel width, roof run, material, ground snow load, seam condition, and the full-roof layout.
Important: Do not select a snow guard based on appearance alone. Although the Dean Steel Buildings profiles in this guide share broad compatibility, the correct product and layout still depend on the actual roof and project conditions. Clamp-on products must match the seam without penetrating it. At the same time, adhesive-mounted guards require a suitable flat bonding surface and proper adhesive application. An incorrect selection or incomplete layout may reduce system performance or damage the roof.

⚡ Dean Steel Buildings Primary Quick Selection Guide

Use this section for fast profile-level guidance. Confirm individual product fit in the complete compatibility chart below.

  • Pro Seam: Compatible with adhesive-mounted polycarbonate guards, SnoBar and ColorBar standing seam systems, RCB-3 rails, 2-bar rails, and SnoCleat RC/RCT.
  • Pro Lok: Offers the same broad selection of adhesive-mounted guards and compatible non-penetrating clamp-on systems.
  • Pro-VR: Compatible with the adhesive and clamp-on product families shown in the chart below.
  • Standing seam warning: Do not attach penetrating screw-down products through these concealed-fastener panels.

About Dean Steel Buildings Roofing Systems

Dean Steel Buildings has served the metal building industry since 1972. The company fabricates building systems for commercial, industrial, institutional, and other construction projects throughout the Southeastern United States, the Caribbean, and Central and South America. Its roofing products include structural standing seam panels engineered for durability, weather resistance, and controlled expansion and contraction. Because panel dimensions and seam designs vary, confirm snow retention compatibility for the specific Dean Steel Buildings profile installed on the roof.

Snow Retention Solutions for Dean Steel Buildings Roofing

Dean Steel Buildings Pro Seam, Pro Lok, and Pro-VR roof systems use concealed fasteners. Compatible snow retention choices may include adhesive-mounted polycarbonate guards installed on an adequate flat panel surface or clamp-on products secured to a suitable seam without penetrating the roof. Never install screw-down snow guards or rail brackets through these standing seam panels.

Explore our complete selection of snow guards for metal roofs, then use the compatibility chart below to compare products by Dean Steel Buildings panel. “YES” means the product is shown as compatible with that profile.

Snow Guards for Dean Steel Buildings Standing Seam Roof Panels

This guide covers Dean Steel Buildings Pro Seam, Pro Lok, and Pro-VR panels. Pro Seam and Pro Lok provide 24-inch coverage with 3-inch seams. Pro Seam uses snapped panel laps, while Pro Lok uses mechanically seamed laps. Pro-VR provides 16-inch coverage with a 2-inch seam. All three profiles can accept the adhesive-mounted polycarbonate guards and compatible clamp-on snow retention systems listed below.

Standing seam warning: Never fasten screw-down snow guards or rail brackets through concealed-fastener standing seam panels. Use an approved clamp-on product when the seam accepts it or an adhesive-mounted guard when the panel pan provides enough flat bonding area.

Would you like additional profile details and installation considerations for these roof systems? Read our complete article: Snow Guards for Dean Steel Buildings Standing Seam Metal Roof Panels.

  Pro Seam Profile Pro Lok Profile Pro-VR Profile
IceJax I
IceJax I		 YES YES YES
IceJax II
IceJax II		 YES YES YES
Ecojax
Ecojax		 YES YES YES
SnoBlox Deuce
SnoBlox Deuce		 YES YES YES
SnoBlox Ace
SnoBlox Ace		 YES YES YES
SnoJax II
SnoJax II		 YES YES YES
SnowBreaker
SnowBreaker		 YES YES YES
SnoBar Standing Seam
SnoBar Standing Seam		 YES YES YES
ColorBar Standing Seam
ColorBar Standing Seam		 YES YES YES
SnoBar RCB-3
SnoBar RCB-3		 YES YES YES
ColorBar RCB-3
ColorBar RCB-3		 YES YES YES
2 Bar SnoBar
2 Bar SnoBar		 YES YES YES
2 Bar ColorBar
2 Bar ColorBar		 YES YES YES
SnoCleat RC
SnoCleat RC		 YES YES YES
SnoCleat RCT
SnoCleat RCT		 YES YES YES

Pro Seam, Pro Lok, and Pro-VR offer broad compatibility with adhesive-mounted polycarbonate guards and non-penetrating clamp-on snow retention systems.

Use SureBond SB-190 only on a suitable, clean bonding surface, and allow about 28 days to cure at 50°F or warmer. Do not use adhesive-mounted guards on copper roofs. Aluminum and copper panels may require additional rail rows because these materials are less rigid than steel.

Test-fit clamp-on components before placing a full order. For areas above walkways, entrances, or parking, consider IceStoppers to help control snow and ice beneath rail systems.

Dean Steel Buildings Snow Guard Buying Checklist

  • Confirm the exact Dean Steel Buildings panel name before choosing a product.
  • Verify the standing seam dimensions and condition before selecting any clamp-on system.
  • Confirm the attachment method: adhesive-mounted or non-penetrating clamp-on.
  • Check the ground snow load. Individual adhesive-mounted guards are generally best suited to lighter snow-load applications. For ground snow loads above 45 psf, we generally recommend a properly designed continuous rail system.
  • Request a layout instead of protecting only isolated areas such as doors, chimneys, or equipment.
  • Order a sample or single unit when you need a test fit. SnoBlox-Snojax products and components have no minimum order requirement.

Need Help Identifying Your Dean Steel Buildings Panel?

If you are not sure which Dean Steel Buildings panel you have, carefully compare the panel profile, review the detailed Dean Steel Buildings blog post linked above, and order a single test-fit unit before committing to a full project. For project-specific help, contact SnoBlox-Snojax at support@snojax.com or call 1-800-766-5291.

Do you have a metal roof from a different manufacturer?

Visit our "Snow Guard Compatibility by Roof Manufacturer" resource page for detailed information on which snow guards and snow retention systems are compatible with your metal roof.

Compatibility Guidance Note

SnoBlox-Snojax bases the compatibility information presented in this guide on product testing and field experience with Dean Steel Buildings metal roof panel profiles. Panel manufacturers periodically update profile specifications, and individual project variables, such as seam condition, coating type, and installation method, can affect outcomes. Customers are encouraged to confirm current panel specifications directly with Dean Steel Buildings and to contact SnoBlox-Snojax with project-specific questions before ordering.

Snow Guards for Dean Steel Buildings Metal Roofing Panels – Compatibility & Installation FAQ

Dean Steel Buildings Pro Seam, Pro Lok, and Pro-VR panels are compatible with adhesive-mounted polycarbonate snow guards and several non-penetrating clamp-on snow retention systems. Compatible options may include IceJax I, IceJax II, Ecojax, SnoBlox Deuce, SnoBlox Ace, SnoJax II, SnowBreaker, SnoBar, ColorBar, RCB-3, 2-Bar, SnoCleat RC, and SnoCleat RCT.
Yes. Ecojax is compatible with the same Dean Steel Buildings panel profiles as SnoBlox Deuce, including Pro Seam, Pro Lok, and Pro-VR.
No. Screw-down snow guards and rail brackets should not penetrate Dean Steel Buildings concealed-fastener standing seam panels. Use compatible clamp-on products or adhesive-mounted guards instead.
This guide covers the Pro Seam, Pro Lok, and Pro-VR standing seam roof panels.
Yes. The Pro Seam, Pro Lok, and Pro-VR profiles may accept compatible clamp-on systems, including SnoBar, ColorBar, RCB-3, 2-Bar, SnoCleat RC, and SnoCleat RCT. We recommend a test fit before ordering a complete system.
No. Compatible clamp-on systems attach directly to the standing seam without penetrating the roof panel.
Yes. You can install adhesive-mounted polycarbonate guards when the panel provides a suitable flat bonding surface. Properly clean and prepare the surface before applying SureBond SB-190 adhesive.
SureBond SB-190 requires approximately 28 days to cure when temperatures remain at or above 50°F. Colder conditions can significantly extend the curing period.
Adhesive-mounted polycarbonate snow guards are not recommended for copper roofing. A compatible clamp-on system may be a better option, depending on the seam profile and project requirements.
They may. Aluminum and copper are less rigid than steel, so you may need additional rows of snow rails to distribute snow loads properly.
Yes. Ordering a single clamp or SnoCleat for a test fit is strongly recommended. Seam dimensions, coatings, and field conditions can affect compatibility.
The required number of rows depends on the roof slope, eave-to-ridge distance, panel width, roof material, ground snow load, and selected product. Complete a full-roof layout before ordering or installing the system.
No. Installing snow guards only in isolated areas can concentrate snow loads and place excessive stress on the roof and snow retention system. A properly designed layout should distribute snow retention products across the entire roof area.
No. Individual adhesive-mounted guards are generally best suited to lighter snow-load applications. Projects with ground snow loads above 45 psf often require a stronger rail-style snow retention system.
Compare the panel width, seam height, seam shape, and profile details with Dean Steel Buildings documentation. If you're still unsure, order a single test-fit component or contact SnoBlox-Snojax at support@snojax.com or 1-800-766-5291.

!