null Skip to main content

Economical 6 Foot SnoBar and ColorBar Snow Rail Kits

See Now

Snow Guards for Steelway Building Systems

Snow guards for Steelway Building Systems roofing panels help manage sudden rooftop releases of snow and ice above entrances, sidewalks, parking areas, loading zones, landscaping, equipment, and other vulnerable locations. The correct SnoBlox-Snojax solution depends on the exact standing-seam concealed-fastener panel installed and the seam geometry, roof conditions, and project requirements.

Compatible Steelway Building Systems snow retention options may include adhesive-mounted polycarbonate guards, non-penetrating clamp-on rail assemblies, RCB-3 rail systems, 2-bar rail systems, and clamp-on SnoCleat products, depending on the standing-seam profile and project requirements.
  • Steelway RTL-24 and CapLoc standing-seam panels require profile-specific attachment methods.
  • Standing-seam panels should use compatible clamp-on systems or adhesive-mounted guards rather than screw-down products.
  • Clamp selection must match the exact standing-seam shape to prevent panel damage and maintain secure attachment.
  • RTL-24 and CapLoc standing-seam profiles support adhesive-mounted polycarbonate guards and several non-penetrating clamp-on systems.
  • Final selection should consider roof slope, panel width, snow load, roof run, roof material, surface striations, and a complete engineered layout.
Important: Do not select a snow guard solely by appearance. A product that fits one Steelway standing-seam profile may not fit another. Clamp-on systems belong only on compatible seams, while adhesive-mounted guards require an appropriate bonding surface and correct installation conditions. Choosing the wrong system can reduce holding strength, damage the panel, or lead to early failure.

⚡ Steelway Building Systems Primary Quick Selection Guide

Use this section for quick profile-level direction. Confirm each product fits in the complete compatibility charts below.

  • RTL-24 panels: Compatible with adhesive-mounted polycarbonate guards, SnoBar/ColorBar standing seam rails, RCB-3 systems, 2-bar rails, and SnoCleat RC/RCT.
  • CapLoc panels: Compatible with adhesive-mounted guards, RCB-3 rails, 2-bar rails, and SnoCleat RCT. Standard standing-seam SnoBar, ColorBar, and SnoCleat RC are not shown as compatible.
  • Standing-seam warning: Never fasten screw-down snow guards through concealed-fastener standing-seam panels.

About Steelway Building Systems Roofing Systems

Steelway Building Systems manufactures pre-engineered steel building solutions for commercial, industrial, institutional, and agricultural projects. This guide focuses on its concealed-fastener standing-seam roofing systems, including RTL-24 and CapLoc. Because these profiles use different seam shapes and attachment geometries, snow guard compatibility must match the exact Steelway panel installed.

Snow Retention Solutions for Steelway Building Systems Roofing

Steelway standing-seam roofs generally require non-penetrating clamp-on systems when the seam shape allows, or adhesive-mounted polycarbonate guards when the panel pan offers a suitable bonding area. The correct attachment method depends on the exact seam profile, panel surface, roof slope, snow load, and complete system layout.

Explore our complete selection of snow guards for metal roofs and use the chart below to verify which SnoBlox-Snojax products fit each Steelway standing-seam panel. “YES” means the product is listed as compatible with that profile. “NO” means it is not shown as a fit.

Snow Guards for Steelway Building Systems Standing Seam Roof Panels

This guide covers Steelway Building Systems RTL-24 and CapLoc standing-seam panels. These profiles differ in seam height, seam shape, panel width, and attachment geometry. Both accept adhesive-mounted polycarbonate guards and selected clamp-on snow retention systems.

Standing seam warning: Do not install screw-down snow guards through concealed-fastener standing-seam roof panels. Use compatible non-penetrating clamp-on products or adhesive-mounted guards where the panel provides an appropriate bonding surface.

Do you need more information about compatible snow guards for Steelway Building Systems standing-seam roof panels? Read the full blog here: Snow Guards for Steelway Building Systems Standing Seam Metal Roof Panels.

RTL-24 and CapLoc panels both accept the adhesive-mounted polycarbonate guards shown in the chart. RTL-24 also supports the standard standing-seam SnoBar, ColorBar, and SnoCleat RC options. At the same time, CapLoc requires the compatible RCT-style attachment options shown above.

Panel striations may require additional adhesive to fill small gaps and limit moisture paths beneath the guard. For rail systems above pedestrian or parking areas, consider IceStopper attachments to help manage snow and ice below the rail.

Steelway Building Systems Snow Guard Buying Checklist

  • Confirm the exact Steelway Building Systems panel name before selecting a product.
  • Confirm the standing-seam profile: RTL-24, CapLoc, or another Steelway concealed-fastener panel.
  • Verify the attachment method: adhesive-mounted or non-penetrating clamp-on.
  • Check ground snow load. Individual adhesive-mounted guards generally work best in lighter snow-load conditions, while higher loads often call for rail systems.
  • Request a layout instead of protecting only isolated locations such as doors, chimneys, or HVAC equipment.
  • Order samples or single units when you need to test fit a product. SnoBlox-Snojax products and components have no minimum order requirement.

Need Help Identifying Your Steelway Building Systems Panel?

If you are not sure which Steelway Building Systems panel you have, carefully compare the panel profile, review the detailed Steelway Building Systems standing-seam blog linked above, and order a single test-fit unit before committing to a full project. For project-specific help, contact SnoBlox-Snojax at support@snojax.com or call 1-800-766-5291.

Do you have a metal roof from a different manufacturer?

Visit our "Snow Guard Compatibility by Roof Manufacturer" resource page for detailed information on which snow guards and snow retention systems are compatible with your metal roof.

Compatibility Guidance Note

SnoBlox-Snojax bases the compatibility information presented in this guide on product testing and field experience with Steelway Building Systems metal roof panel profiles. Panel manufacturers periodically update profile specifications, and individual project variables, such as seam condition, coating type, and installation method, can affect outcomes. Customers are encouraged to confirm current panel specifications directly with Steelway Building Systems and to contact SnoBlox-Snojax with project-specific questions before ordering.

Snow Guards for Steelway Building Systems Metal Roofing Panels – Compatibility & Installation FAQ

The correct snow guard depends on the specific Steelway Building Systems roof panel. Standing seam panels typically work with compatible clamp-on snow retention systems or adhesive-mounted polycarbonate snow guards. Exposed fastener panels may work with adhesive-mounted guards, screw-fastened snow guards, SnowCatcher products, SnoBar PBR, ColorBar PBR, or other compatible systems depending on the panel profile.
Yes. Many Steelway Building Systems standing seam roof panels accept non-penetrating clamp-on snow retention systems that attach directly to the standing seams. Some standing seam profiles also work with adhesive-mounted polycarbonate snow guards when the panel pan provides an appropriate bonding surface.
This compatibility guide includes Steelway Building Systems RTL-24 and CapLoc standing seam roof panels.
This guide covers the ExSteel StormSeal exposed fastener roof panel associated with Steelway Building Systems.
No. Do not install screw-fastened snow guards through concealed-fastener standing seam roof panels. Use compatible clamp-on snow retention systems or adhesive-mounted polycarbonate snow guards designed for the specific panel profile.
Yes. Compatible standing seam panels may support SnoBar, ColorBar, RCB-3 rail systems, 2-Bar systems, and compatible SnoCleat clamp-on products depending on the seam profile.
Yes, if the panel profile supports them. Install screw-fastened products through the low flats of the panel into adequate structural support. Do not fasten snow retention products directly through the panel ribs.
In most cases, yes. Installing snow guards only above doors, walkways, HVAC equipment, or other isolated areas can concentrate snow loads and reduce overall system performance. A properly engineered layout distributes loads more effectively across the roof.
Compare your roof profile with the panel photos and descriptions in our Steelway Building Systems compatibility guides. If you are still unsure, contact SnoBlox-Snojax for assistance or order a single test-fit product before placing a larger order.
Different Steelway Building Systems roof panels use different seam shapes, rib configurations, and attachment methods. Choosing a snow retention system designed specifically for your panel helps ensure proper fit, long-term performance, and reliable snow retention.
Yes. Ground snow load, roof slope, roof length, panel type, and building design all influence product selection. Higher snow load regions often require engineered rail systems instead of individual snow guards.
Visit our Roof Manufacturer Compatibility resource to compare snow guard compatibility across hundreds of standing seam and exposed fastener metal roof panel profiles.

!