Snow Guards for AB Martin Metal Roofing
Snow guards for AB Martin roofing panels help control rooftop snow and ice movement above doors, sidewalks, parking areas, driveways, landscaping, mechanical equipment, and other locations where sliding snow can create safety or property-damage concerns. The correct SnoBlox-Snojax product depends on whether the roof uses the ABSeam standing-seam concealed-fastener panel or one of AB Martin's exposed-fastener roof profiles.
Compatible AB Martin snow retention options may include adhesive-mounted polycarbonate guards, screw-fastened guards, SnowCatcher products, PBR-style rail systems, non-penetrating clamp-on rail assemblies, RCB-3 rail systems, 2-bar rail systems, 2.67 corrugated systems, and clamp-on SnoCleat products, depending on the panel geometry.
- AB Martin standing-seam and exposed-fastener panels require different snow-retention attachment methods.
- ABSeam standing seam panels should use compatible clamp-on systems or adhesive-mounted guards, not screw-down attachments through the panel.
- ABM, PBR, 5V Crimp, and Heritage exposed-fastener panels may accept adhesive-mounted guards, screw-down guards, SnowCatcher products, PBR rail systems, or 2.67 systems, depending on the exact panel profile.
- We did not include the continuous corrugated panels from AB Martin because AB Martin does not recommend those profiles for roofing applications.
- Final product selection should account for roof slope, panel width, snow load, run length, roof material, panel texture, structural attachment, and full-roof layout requirements.
Important: Do not select snow guards based solely on appearance. A product that fits one AB Martin panel may not fit another. Clamp-on systems are intended only for compatible standing-seam profiles. At the same time, exposed-fastener panels may require adhesive bonding, screw-down attachment, PBR brackets, Tall ColorBrackets, or 2.67 corrugated brackets. An incorrect selection can reduce holding strength, increase leak risk, or cause premature system failure.
⚡ AB Martin Primary Quick Selection Guide
Use this section for fast profile-level direction. Confirm the exact product fit in the full compatibility charts below.
- ABSeam standing seam panel: Broad compatibility with adhesive-mounted polycarbonate guards, SnoBar/ColorBar standing seam rails, RCB-3 systems, 2-bar rails, and SnoCleat RC/RCT.
- ABM exposed-fastener panel: Compatible with EcoJax, SnoBlox Deuce, IceJax I, SnoJax I, SnowBreaker, SnowCatcher, SnoCleat PBR, SnoBar PBR, and ColorBar PBR.
- PBR, 5V Crimp, and Heritage panels: Accept the widest range of exposed-fastener snow retention options, including selected polycarbonate guards, SnowCatcher, SnoCleat PBR, SnoBar PBR, and ColorBar PBR.
- 5V Crimp panel: Also works with 2.67 corrugated systems shown in the chart.
- Continuous corrugated panels: Not included in the chart because AB Martin does not recommend those panels for roofing.
About AB Martin Roofing Systems
AB Martin began in 1947 and has grown into a regional supplier of metal roofing, siding, construction materials, accessories, and custom-length metal panels. The company serves contractors, builders, homeowners, and agricultural projects throughout Pennsylvania and nearby Mid-Atlantic markets. AB Martin's roofing lineup includes the ABSeam standing-seam panel, along with exposed-fastener options such as ABM, PBR, 5V Crimp, and Heritage. Because these panels differ in seam height, rib spacing, panel width, fastening method, surface texture, and available low-flat mounting area, snow guard compatibility must match the exact profile installed.
Snow Retention Solutions for AB Martin Roofing
AB Martin manufactures both concealed-fastener standing seam roof panels and exposed-fastener metal roof panels. Those roof styles do not manage snow retention the same way. Standing seam roofs typically require non-penetrating clamp-on systems when the seam shape allows it, or adhesive-mounted guards when the panel has a suitable flat bonding surface. Exposed-fastener panels may accept screw-down products when fastened through the low flats and into adequate structure.
See our full range of snow guards for metal roofs and use the charts below to confirm which SnoBlox-Snojax products fit each AB Martin panel. “YES” indicates the product is shown as a fit for that panel. “NO” means it is not shown as compatible for that profile.
Snow Guards for AB Martin Standing Seam Roof Panels
AB Martin's primary standing seam roofing profile is the ABSeam panel. It uses a concealed clip system and a 1-1/2 inch seam, with panel width and finish options that can vary by gauge. Its broad pan area and seam shape allow several adhesive-mounted and clamp-on snow-retention options when project conditions are appropriate.
Standing seam warning: Do not install screw-down snow guards through concealed-fastener standing-seam roof panels. Use compatible clamp-on products where the seam accepts them, or adhesive-mounted guards where a flat bonding surface is available.
Do you need more information about our compatible snow guards for AB Martin standing-seam roof panels? Check out our full blog here: Snow Guards for Standing Seam Metal Roof Panels by AB Martin.
| ABSeam Profile | |
|---|---|
 IceJax I |
YES |
 IceJax II |
YES |
 EcoJax |
YES |
 SnoBlox Deuce |
YES |
 SnoBlox Ace |
YES |
 SnoJax II |
YES |
 SnowBreaker |
YES |
 SnoBar Standing Seam |
YES |
 ColorBar Standing Seam |
YES |
 SnoBar RCB-3 |
YES |
 ColorBar RCB-3 |
YES |
 2 Bar SnoBar |
YES |
 2 Bar ColorBar |
YES |
 SnoCleat RC |
YES |
 SnoCleat RCT |
YES |
The ABSeam profile offers broad standing-seam compatibility because it can accept many adhesive-mounted guards and compatible clamp-on snow-retention systems.
EcoJax is included directly above SnoBlox Deuce because it is a polycarbonate snow guard and follows the same compatibility shown for SnoBlox Deuce on this AB Martin standing seam chart.
Textured or striated panel surfaces may require a heavier adhesive application to fill small gaps and reduce moisture paths beneath the guard. If using a rail system, IceStopper attachments are recommended above pedestrian or parking areas to help manage snow and ice beneath the rail.
Snow Guards for AB Martin Exposed Fastener Roof Panels
AB Martin exposed-fastener profiles include ABM, PBR, 5V Crimp, and Heritage. These panels do not all provide the same rib spacing, high-rib shape, surface texture, or low-flat mounting area, so compatibility changes significantly by profile.
Exposed fastener reminder: When screw-down snow guards or rails are compatible, they should be attached through the low flats of the panel and into adequate structure. Do not mount screw-down snow retention products only to the high ribs or only into the panel skin.
Do you need more information about our compatible snow guards for AB Martin exposed-fastener roof panels? Check out our full blog here: Snow Guards for Exposed Fastener Metal Roof Panels by AB Martin.
| ABM Profile | PBR Profile | 5V Crimp Profile | Heritage Profile | |
|---|---|---|---|---|
| IceJax I |
YES | YES | YES | YES |
| IceJax II |
NO | YES | YES | YES |
| EcoJax |
YES | YES | YES | YES |
| SnoBlox Deuce |
YES | YES | YES | YES |
| SnoBlox Ace |
NO | YES | YES | YES |
 SnoJax I |
YES | YES | YES | YES |
| SnoJax II |
NO | YES | YES | YES |
| SnowBreaker |
YES | YES | YES | YES |
 SnowCatcher |
YES | YES | YES | YES |
 SnoCleat PBR |
YES | YES | YES | YES |
 SnoCleat 2.67 |
NO | NO | YES | YES |
 SnoBar PBR |
YES | YES | YES | YES |
 ColorBar PBR |
YES | YES | YES | YES |
 SnoBar 2.67 |
NO | NO | NO | NO |
 ColorBar 2.67 |
NO | NO | NO | NO |
The PBR, 5V Crimp, and Heritage profiles accept the widest range of exposed-fastener snow retention options, including selected polycarbonate snow guards, SnowCatcher, SnoCleat PBR, and PBR-style rail systems.
The ABM panel has more limited pad-style compatibility than the other exposed-fastener profiles. Still, it remains compatible with EcoJax, SnoBlox Deuce, IceJax I, SnoJax I, SnowBreaker, SnowCatcher, SnoCleat PBR, SnoBar PBR, and ColorBar PBR.
When using screw-down products, always verify that the fasteners engage adequate structure beneath the panel. When using adhesive-mounted polycarbonate guards, follow the recommended adhesive and cure-time guidance for the project conditions.
AB Martin Snow Guard Buying Checklist
- Confirm the exact AB Martin panel name before choosing any product.
- Identify the roof type: standing seam, concealed fastener, exposed fastener, PBR-style, or corrugated.
- Verify the attachment method: adhesive, screw-down, clamp-on, PBR bracket, or 2.67 corrugated bracket.
- Check ground snow load. Individual glue-down or screw-down guards are generally best suited for lighter snow-load applications. At the same time, higher loads often require rail systems.
- Request a layout rather than installing only in isolated areas such as doors, chimneys, or HVAC equipment.
- Order samples or single units when a test fit is needed. SnoBlox-Snojax products and components are available with no minimum order requirement.
Need Help Identifying Your AB Martin Panel?
If you are not sure which AB Martin panel you have, compare the panel profile carefully, review the two detailed AB Martin blog posts linked above, and order a single test-fit unit before committing to a full project. For project-specific help, contact SnoBlox-Snojax at support@snojax.com or call 1-800-766-5291.
Do you have a metal roof from a different manufacturer?
Visit our "Snow Guard Compatibility by Roof Manufacturer" resource page for detailed information on which snow guards and snow retention systems are compatible with your metal roof.
Compatibility Guidance Note
SnoBlox-Snojax bases the compatibility information presented in this guide on product testing and field experience with AB Martin metal roof panel profiles. Panel manufacturers periodically update profile specifications, and individual project variables, such as seam condition, coating type, and installation method, can affect outcomes. Customers are encouraged to confirm current panel specifications directly with AB Martin and to contact SnoBlox-Snojax with project-specific questions before ordering.
Snow Guards for AB Martin Metal Roofing Panels – Compatibility & Installation FAQ
The correct snow guard for an AB Martin metal roof depends on the specific panel profile installed. Some AB Martin standing seam panels can use adhesive-mounted snow guards, clamp-on snow retention systems, SnoCleat products, and rail-style systems such as SnoBar and ColorBar. Exposed fastener panels may require screw-down products, PBR systems, or corrugated-specific snow retention systems. Always identify the exact panel before selecting a snow retention system.
The easiest way to identify an AB Martin roof panel is to compare the seam shape, rib height, rib spacing, and panel width to manufacturer literature or installation documentation. If you're unsure which panel you have, our team can help identify it using photos and measurements.
We recommend snow guards anywhere sliding snow or ice could create a safety hazard or damage property. Common areas include entrances, walkways, driveways, parking areas, patios, HVAC equipment, landscaping, and lower roof sections.
Yes. You can install most of our snow retention systems on existing AB Martin metal roofs. The appropriate attachment method depends on the panel profile and may include adhesive bonding, clamp-on attachment, or mechanical fastening.
Many AB Martin standing seam panels are compatible with clamp-on systems such as SnoBar, ColorBar, SnoCleat RC, SnoCleat RCT, and RCB-3 systems. Some profiles may also accept adhesive-mounted polycarbonate snow guards. The best option depends on roof slope, snow load, panel type, and project goals.
Yes. Many AB Martin exposed fastener panels are compatible with polycarbonate snow guards, SnowCatcher products, PBR-style systems, and corrugated-specific snow retention systems. Product selection depends on the panel's rib geometry and available mounting surface.
Not always. Many standing-seam panels can use clamp-on snow retention systems. Still, some profiles are better suited to adhesive-mounted products. Compatibility depends on seam design, seam height, panel material, and roof configuration.
The number of snow guards required depends on roof dimensions, roof pitch, panel type, snow load, roof material, and the chosen snow retention system. A proper layout should distribute loads across the roof system rather than relying on a small number of individual guards.
Individual snow guards help break up and control snow movement across the roof surface or retain the snow and ice until it can melt safely into the building's gutters. Rail systems such as SnoBar and ColorBar can support higher snow loads. Installers prefer them for commercial buildings, high-snow regions, and areas above pedestrian traffic.
When the correct product is selected and installed according to manufacturer recommendations, snow guards should not damage the roof. Problems typically occur when installers use incompatible products on the wrong panel profile or when attachment methods are not appropriate for the roof system.
Yes. Snow retention systems appear on agricultural facilities, commercial buildings, retail locations, churches, warehouses, offices, and residential properties that use AB Martin roofing panels.
If you're unsure which AB Martin panel you have, contact SnoBlox-Snojax with photos and basic roof information. Our team can help identify the panel and recommend compatible snow guards, snow rails, or complete snow retention systems for your project.
The ABSeam standing seam panel is compatible with adhesive-mounted polycarbonate snow guards, SnoCleat systems, SnoBar systems, ColorBar systems, and double-bar rail systems. Compatibility should always be verified against the latest manufacturer specifications.