null Skip to main content

Economical 6 Foot SnoBar and ColorBar Snow Rail Kits

See Now

Snow Guards for Elevate (Firestone)

Snow guards for Elevate (formerly Firestone Building Products) roofing panels help manage rooftop snow and ice above entrances, sidewalks, parking areas, equipment, landscaping, and other locations where an unexpected release could create safety concerns or property damage. Choosing the right SnoBlox-Snojax solution starts with determining whether the roof is a standing-seam concealed-fastener system or an exposed-fastener panel, then confirming the exact Elevate profile.

Compatible Elevate snow retention options may include adhesive-mounted polycarbonate guards, mechanically fastened individual guards, SnowCatcher products, non-penetrating clamp-on rails, RCB-3 and 2-bar assemblies, PBR-style systems, 2.67 corrugated systems, and clamp-on SnoCleat products. Compatibility varies by panel geometry.
  • Elevate standing-seam and exposed fastener panels require different attachment methods.
  • UC-3, UC-4, UC-6, and UC-14 standing-seam panels accept compatible adhesive-mounted guards and clamp-on systems.
  • UC-7 is a batten-cap profile, so adhesive-mounted polycarbonate guards are compatible, but clamp-on products are not recommended.
  • Exposed fastener compatibility varies substantially among the Omega, 5 V-Crimp, UC-600, and UC-601 profiles.
  • Final selection should consider panel dimensions, roof slope and run length, snow load, roof material, attachment structure, and the full-roof layout.
Important: Never select a snow guard solely by appearance. A product compatible with one Elevate profile may not fit another. Standing-seam systems require adhesive attachment or suitable non-penetrating clamps. Meanwhile, exposed-fastener panels may call for adhesive bonding, structural screw attachment, PBR brackets, or corrugated-panel brackets. Using the wrong attachment can reduce holding strength, damage the roof, or increase leak and failure risks.

⚡ Elevate (Firestone) Quick Selection Guide

Use this overview for quick profile-level guidance, then confirm the exact fit in the full charts below.

  • UC-3, UC-4, UC-6, and UC-14: Compatible with adhesive-mounted polycarbonate guards, SnoBar and ColorBar standing-seam rails, RCB-3 systems, 2-bar systems, and SnoCleat RC/RCT.
  • UC-7: Compatible with adhesive-mounted polycarbonate guards on flat roof areas. Do not use clamp-on systems on its batten cap.
  • Omega VR Classic, Omega UR Pro, Omega HR Ultra, and 5 V-Crimp: Compatible options vary by the available flat mounting area and panel geometry; see the exposed fastener chart.
  • UC-600: Compatible with SnoCleat 2.67, SnoBar 2.67, and ColorBar 2.67.
  • UC-601: No compatible SnoBlox-Snojax system is currently shown because its 2-inch corrugation does not match 2.67-inch brackets and does not provide a suitable flat mounting surface.

About Elevate (Firestone) Roofing Systems

Elevate traces its roots to Firestone Building Products, a long-established manufacturer of commercial roofing, wall, and lining systems. Holcim acquired Firestone Building Products in 2021 and rebranded the company as Elevate in 2022. In 2025, Holcim spun off its North American business as Amrize, making Elevate part of the Amrize family of brands. Today, Elevate continues to build on its Firestone heritage while offering roofing and building envelope solutions under the Amrize organization.

Snow Retention Solutions for Elevate Roofing

Elevate standing-seam and exposed fastener panels cannot be treated as one attachment category. Concealed-fastener standing-seam panels generally require non-penetrating clamps that match the seam or adhesive-mounted guards placed on suitable flat pans. Exposed-fastener panels may accept screw-down products when fasteners pass through appropriate mounting areas and engage adequate structure.

Browse our complete selection of snow guards for metal roofs and use the following charts to match products with individual Elevate profiles. “YES” identifies a listed fit, while “NO” means the product is not shown as compatible with that panel.

Snow Guards for Elevate (Firestone) Standing Seam Metal Roof Panels

The standing-seam group includes UC-3, UC-4, UC-6, UC-14, and UC-7. The first four profiles can use both adhesive-mounted polycarbonate snow guards and compatible clamp-on systems. UC-7 uses a batten-cap seam, which limits it to adhesive-mounted guards installed on suitable flat areas.

Standing-seam warning: Do not drive screw-down fasteners through concealed-fastener standing-seam panels. Use a compatible non-penetrating clamp system or an adhesive-mounted guard where the panel provides a flat bonding surface. Pad-style guards are not appropriate on curved roof areas.

Do you need more information about compatible snow guards for Elevate standing-seam roof panels? Read our complete guide: Snow Guards for Elevate (Firestone) Standing Seam Metal Roof Panels.

  UC-3 Profile UC-4 Profile UC-6 Profile UC-14 Profile UC-7 Profile
IceJax I
IceJax I 		YES YES YES YES YES
IceJax II
IceJax II 		YES YES YES YES YES
Ecojax
Ecojax 		YES YES YES YES YES
SnoBlox Deuce
SnoBlox Deuce 		YES YES YES YES YES
SnoBlox Ace
SnoBlox Ace 		YES YES YES YES YES
SnoJax II
SnoJax II 		YES YES YES YES YES
SnowBreaker
SnowBreaker 		YES YES YES YES YES
SnoBar Standing Seam
SnoBar Standing Seam 		YES YES YES YES NO
ColorBar Standing Seam
ColorBar Standing Seam 		YES YES YES YES NO
SnoBar RCB-3
SnoBar RCB-3 		YES YES YES YES NO
ColorBar RCB-3
ColorBar RCB-3 		YES YES YES YES NO
2 Bar SnoBar
2 Bar SnoBar 		YES YES YES YES NO
2 Bar ColorBar
2 Bar ColorBar 		YES YES YES YES NO
SnoCleat RC
SnoCleat RC 		YES YES YES YES NO
SnoCleat RCT
SnoCleat RCT 		YES YES YES YES NO

UC-3, UC-4, UC-6, and UC-14 are broadly compatible with adhesive-mounted guards and non-penetrating clamp-on snow retention systems.


UC-7 requires special attention because clamps attached to its batten cap could disengage the cap and damage the roof. On flat sections, compatible adhesive-mounted guards are the appropriate option. Aluminum and copper roofs may require additional rail rows compared with steel systems.

Snow Guards for Elevate (Firestone) Exposed Fastener Roof Panels

This exposed-fastener section covers Omega VR Classic, Omega UR Pro, Omega HR Ultra, 5 V-Crimp, UC-600, and UC-601. Their rib patterns and flat mounting areas differ considerably, so the compatible products range from individual polycarbonate guards and screw-down rails to 2.67 corrugated systems. UC-601 currently has no listed solution.

Exposed fastener reminder: Unless a product is specifically designed for rib mounting, screw-down guards and rail brackets should attach through the panel’s low, flat mounting areas and into sufficient structure. Do not rely on the sheet metal alone for support.

Do you need more information about compatible snow guards for Elevate exposed-fastener roof panels? Read our complete guide: Snow Guards for Elevate (Firestone) Exposed Fastener Metal Roof Panels.

  Omega VR Classic Panel Omega UR Pro Panel Omega HR Ultra Panel 5 V-Crimp Panel UC-600 Panel UC-601 Panel
IceJax I
IceJax I 		NO YES YES YES NO NO
IceJax II
IceJax II 		NO NO YES YES NO NO
Ecojax
Ecojax 		YES YES YES YES NO NO
SnoBlox Deuce
SnoBlox Deuce 		YES YES YES YES NO NO
SnoBlox Ace
SnoBlox Ace 		NO YES YES YES NO NO
SnoJax I
SnoJax I 		NO NO YES YES NO NO
SnoJax II
SnoJax II 		NO NO YES YES NO NO
SnowBreaker
SnowBreaker 		YES YES YES YES NO NO
SnowCatcher
SnowCatcher 		NO NO YES YES NO NO
SnoCleat PBR
SnoCleat PBR 		NO YES YES YES NO NO
SnoCleat 2.67
SnoCleat 2.67 		NO NO NO YES YES NO
SnoBar PBR
SnoBar PBR 		YES YES YES YES NO NO
ColorBar PBR
ColorBar PBR 		YES YES YES YES NO NO
SnoBar 2.67
SnoBar 2.67 		NO NO NO YES YES NO
ColorBar 2.67
ColorBar 2.67 		NO NO NO YES YES NO

Omega VR Classic accepts SnoBlox Deuce, Ecojax, SnowBreaker, SnoBar PBR, and ColorBar PBR. Omega UR Pro adds selected smaller polycarbonate guards and PBR-style products. Omega HR Ultra and 5 V-Crimp provide the broadest exposed-fastener compatibility in this group.

UC-600’s corrugated geometry works with SnoCleat 2.67, SnoBar 2.67, and ColorBar 2.67. UC-601 has approximately 2-inch rib spacing, so it is incompatible with both the 2.67-inch bracket family and products that require a flat base.

For screw-down systems, fasteners must engage adequate structure. Adhesive-mounted products require suitable panel material, surface preparation, and the complete SureBond SB-190 curing period.

Elevate (Firestone) Snow Guard Buying Checklist

  • Confirm the exact Elevate panel name before selecting a snow guard or rail system.
  • Identify the roof category: standing-seam, batten cap, exposed fastener, PBR-style, or corrugated.
  • Match the attachment method: adhesive, structural screw-down, seam clamp, PBR bracket, or 2.67 corrugated bracket.
  • Check the ground snow load. Individual adhesive-mounted or screw-down guards are generally best suited to lighter snow-load applications. Heavier conditions often require professionally designed rail-system layouts.
  • Request a complete layout instead of concentrating snow retention only above entrances, chimneys, equipment, or walkways.
  • Order a test-fit component when seam or panel compatibility needs confirmation. SnoBlox-Snojax products are available without minimum-order requirements.

Need Help Identifying Your Elevate (Firestone) Panel?

If you are not sure which Elevate (Firestone) panel you have, carefully compare the panel profile, review the two detailed Elevate (Firestone) blog posts linked above, and order a single test-fit unit before committing to a full project. For project-specific help, contact SnoBlox-Snojax at support@snojax.com or call 1-800-766-5291.

Do you have a metal roof from a different manufacturer?

Visit our "Snow Guard Compatibility by Roof Manufacturer" resource page for detailed information on which snow guards and snow retention systems are compatible with your metal roof.

Compatibility Guidance Note

SnoBlox-Snojax bases the compatibility information presented in this guide on product testing and field experience with Elevate (Firestone) metal roof panel profiles. Panel manufacturers periodically update profile specifications, and individual project variables such as seam condition, coating type, and installation method can affect outcomes. Customers are encouraged to confirm current panel specifications directly with Elevate (Firestone) and to contact SnoBlox-Snojax with project-specific questions before ordering.

Snow Guards for Elevate (Firestone) Steel Roofing Panels – Compatibility & Installation FAQ

SnoBlox-Snojax does not currently list a compatible system for the UC-601. Its approximately 2-inch corrugation does not fit products designed for 2.67-inch corrugated panels, and its wavy surface does not provide the flat mounting area required by other systems.
Clamp-on snow guards and rail systems are not recommended for the UC-7 because they would attach to the batten cap rather than securely clamping the main panel seam. Adhesive-mounted polycarbonate guards may be used where the roof provides a suitable flat installation surface.

The Elevate UC-600 is compatible with SnoCleat 2.67, SnoBar 2.67, and ColorBar 2.67 systems. These products are designed to follow the geometry of compatible 2.67-inch corrugated roofing panels.

No. Do not drive screws through concealed-fastener standing seam panels. Elevate UC-3, UC-4, UC-6, and UC-14 roofs should use compatible non-penetrating clamp-on systems or adhesive-mounted guards installed on appropriate flat surfaces.

Omega HR Ultra and 5 V-Crimp have the broadest compatibility among the exposed fastener panels covered in this guide. Compatible options include selected polycarbonate guards, SnowCatcher, SnowBreaker, PBR-style systems, and certain 2.67 corrugated products, as shown in the compatibility chart.
These standing seam profiles are compatible with adhesive-mounted polycarbonate guards, SnoBar and ColorBar standing seam systems, RCB-3 systems, 2-bar systems, and SnoCleat RC/RCT. Confirm the seam dimensions and test-fit clamp components before ordering a complete system.
Compatible options for Omega VR Classic include Ecojax, SnoBlox Deuce, SnowBreaker, SnoBar PBR, and ColorBar PBR. Product placement and attachment must follow a complete layout designed for the panel geometry and project conditions.
Pad-style snow guards require a flat mounting surface and should not be installed across curved roof areas. A properly designed rail system may be a better option when the panel profile and seam can accept compatible clamps.
PBR systems attach through the low, flat areas of compatible exposed fastener panels. SnoCleat 2.67, SnoBar 2.67, and ColorBar 2.67 use brackets shaped for compatible corrugated profiles and are not interchangeable with standard PBR brackets.
Yes. Seam dimensions and shapes can vary between panel models and production generations. Ordering a clamp or individual component for a physical test fit helps confirm compatibility before purchasing a complete snow retention system.
SureBond SB-190 requires about 28 days at temperatures of 50°F or higher to fully cure. Schedule adhesive installations during suitable weather, and properly clean and prepare the roof surface before installation.
Snow guards should generally be distributed across the roof according to a complete layout rather than concentrated only above isolated areas. Installing a short section in one location can overload the system and place excessive stress on the roof panels or attachments.
Confirm the exact panel name, seam or rib dimensions, roof material, panel width, roof slope, eave length, roof run, and project location. These details help determine product compatibility, attachment method, required rows, and the appropriate layout.

Compare the roof profile with the panel descriptions and images in the Elevate standing seam and exposed fastener guides. You can also order a single product or clamp for test fitting or contact SnoBlox-Snojax at support@snojax.com or 1-800-766-5291 for project-specific assistance.

!