Snow Guards for North Star Metals
Snow guards for North Star Metals roof panels help manage snow and ice buildup above building entrances, sidewalks, vehicles, landscaping, and equipment. Selecting an appropriate system begins with identifying the roof as either a concealed-fastener standing seam or exposed-fastener panel and confirming its exact profile.
- Standing seam and exposed fastener panels require different snow retention attachment methods.
- Standing seam roofs should use suitable adhesive-mounted guards or compatible non-penetrating clamps rather than screw-down products.
- Five Star and En-Dura Star panels may accommodate individual snow guards, SnowCatcher, SnoCleat PBR, and PBR rail systems.
- Loc Star and Snap Star offer broad adhesive and clamp-on compatibility, while NS-18 requires more selective placement of individual guards.
- Roof pitch, panel dimensions, snow load, roof material, slope length, and full-roof layout requirements influence the final system recommendation.
⚡ North Star Metals Quick Selection Guide
Use this section for fast profile-level direction. Confirm the exact product fit in the full compatibility charts below.
- Loc Star and Snap Star: These 16-inch standing seam profiles support adhesive-mounted polycarbonate guards, compatible SnoBar/ColorBar clamp-on rails, RCB-3 assemblies, 2-bar systems, and SnoCleat RC/RCT.
- NS-18: Compatible individual guards include IceJax I, EcoJax, SnoBlox Deuce, SnoBlox Ace, and SnowBreaker. IceJax II and SnoJax II are not listed as compatible. Appropriate clamp-on rails and SnoCleat systems remain options once the seam configuration is confirmed.
- Five Star: Suitable options include selected smaller-footprint snow guards, SnowCatcher, SnoCleat PBR, and PBR rails. IceJax II, SnoBlox Ace, and SnoJax II are not listed as compatible.
- En-Dura Star: Its available mounting areas accommodate a wider selection of individual guards, SnowCatcher, SnoCleat PBR, and PBR rail assemblies.
- Attachment warning: Never install screw-down snow guards through concealed-fastener standing seams. Exposed-fastener systems require appropriate low-flat mounting locations and adequate structural attachment.
About North Star Metals Roofing Systems
North Star Metals MFG Co., established in 1994, manufactures metal roofing, siding, and custom trim products for residential, agricultural, commercial, and industrial applications. Its roof panel selection includes concealed-fastener standing seam systems and exposed-fastener profiles. Because dimensions, rib arrangements, and available mounting surfaces differ, snow guard selection must match the exact North Star Metals panel installed.
Snow Retention Solutions for North Star Metals Roofing
North Star Metals roofing systems require attachment methods suited to their panel construction. Standing seam panels can use properly matched non-penetrating clamps or adhesive-mounted polycarbonate guards where bonding surfaces are adequate. Exposed-fastener panels may support mechanically attached guards and rail brackets when installers secure the system through appropriate panel flats into sufficient structural support.
Explore our complete selection of snow guards for metal roofs, and consult the charts below for North Star Metals panel compatibility. A green YES identifies a listed compatible product. In contrast, a red NO identifies a product not shown as suitable for that profile.
Snow Guards for North Star Metals Standing Seam Roof Panels
This section compares Loc Star, Snap Star, and NS-18 concealed-fastener roofing profiles. Loc Star and Snap Star feature 16-inch panel widths with approximately 1.5-inch seams. NS-18 uses an 18-inch panel width and a 2-3/8-inch seam. Differences in seam configuration, pan width, and mounting surface determine individual guard compatibility and the clamps appropriate for rail installations.
Standing seam warning: Do not install screw-down snow guards through concealed-fastener standing-seam roof panels. Use compatible clamp-on products where the seam accepts them, or adhesive-mounted guards where a flat bonding surface is available.
Need more information about our compatible snow guards for North Star Metals standing-seam roof panels? Check out our full blog here: Snow Guards for North Star Metals MFG Co Standing Seam Metal Roof Panels.
| Product | Loc Star Panel | Snap Star Panel | NS-18 Panel |
|---|---|---|---|
![]() IceJax I |
YES | YES | YES |
![]() IceJax II |
YES | YES | NO |
![]() EcoJax |
YES | YES | YES |
![]() SnoBlox Deuce |
YES | YES | YES |
![]() SnoBlox Ace |
YES | YES | YES |
![]() SnoJax II |
YES | YES | NO |
![]() SnowBreaker |
YES | YES | YES |
![]() SnoBar Standing Seam |
YES | YES | YES |
![]() ColorBar Standing Seam |
YES | YES | YES |
![]() SnoBar RCB-3 |
YES | YES | YES |
![]() ColorBar RCB-3 |
YES | YES | YES |
![]() 2 Bar SnoBar |
YES | YES | YES |
![]() 2 Bar ColorBar |
YES | YES | YES |
![]() SnoCleat RC |
YES | YES | YES |
![]() SnoCleat RCT |
YES | YES | YES |
Loc Star and Snap Star provide numerous adhesive-mounted guard and compatible clamp-on system options. NS-18 has a more limited selection of individual guards. However, compatible rail and SnoCleat assemblies remain available when the proper clamps match its seam.
Striated panels may require additional adhesive to fill surface gaps and limit moisture paths. IceStopper attachments are recommended with rail systems above pedestrian areas and parking spaces to help control snow and ice beneath the rails.
Snow Guards for North Star Metals Exposed Fastener Roof Panels
North Star Metals Five Star and En-Dura Star exposed-fastener roofing profiles provide different mounting areas for snow retention products. Five Star requires more selective placement of individual guards, while En-Dura Star accommodates a wider range of pad-style snow guards. Both profiles may support SnowCatcher, SnoCleat PBR, SnoBar PBR, and ColorBar PBR systems when the installation meets structural attachment requirements.
Exposed fastener reminder: When screw-down snow guards or rails are compatible, attach them through the low flats of the panel and into adequate structure. Do not install individual snow guards or rail systems directly on the panel's high ribs.
Need more information about our compatible snow guards for North Star Metals exposed-fastener roof panels? Check out our full blog here: Snow Guards for North Star Metals MFG Co Exposed Fastener Metal Roof Panels.
| Product | Five Star Panel | En-Dura Star Panel |
|---|---|---|
![]() IceJax I |
YES | YES |
![]() IceJax II |
NO | YES |
![]() EcoJax |
YES | YES |
![]() SnoBlox Deuce |
YES | YES |
![]() SnoBlox Ace |
NO | YES |
![]() SnoJax I |
YES | YES |
![]() SnoJax II |
NO | YES |
![]() SnowBreaker |
YES | YES |
![]() SnowCatcher |
YES | YES |
![]() SnoCleat PBR |
YES | YES |
![]() SnoCleat 2.67 |
NO | NO |
![]() SnoBar PBR |
YES | YES |
![]() ColorBar PBR |
YES | YES |
![]() SnoBar 2.67 |
NO | NO |
![]() ColorBar 2.67 |
NO | NO |
Five Star and En-Dura Star both accommodate selected adhesive-mounted polycarbonate snow guards, SnowCatcher, SnoCleat PBR, and PBR rail systems. En-Dura Star offers additional individual guard choices because its panel geometry provides suitable mounting areas for larger products.
SnoCleat 2.67, SnoBar 2.67, and ColorBar 2.67 are not compatible with these panels. These products require the specific geometry of 2.67-inch corrugated roofing.
Screw-down products require secure attachment into adequate underlying structure. Adhesive-mounted polycarbonate guards must follow SureBond SB-190 curing requirements, and we do not recommend adhesive installations on copper roofing.
North Star Metals Snow Guard Buying Checklist
- Confirm the exact North Star Metals panel name before choosing any product.
- Identify the roof type: standing seam, concealed fastener, exposed fastener, PBR-style, or corrugated.
- Verify the attachment method: adhesive, screw-down, clamp-on, PBR bracket, or 2.67 corrugated bracket.
- Check ground snow load. Individual glue-down or screw-down guards generally suit lighter snow-load applications. Higher loads often require rail systems.
- Request a layout rather than installing only in isolated areas such as doors, chimneys, or HVAC equipment.
- Order samples or single units when you need a test fit. SnoBlox-Snojax products and components are available with no minimum order requirement.
Related Resources
Need Help Identifying Your North Star Metals Panel?
If you are not sure which North Star Metals panel you have, carefully compare the panel profile, review the two detailed North Star Metals blog posts linked above, and order a single test-fit unit before committing to a full project. For project-specific help, contact SnoBlox-Snojax at support@snojax.com or call 1-800-766-5291.
Do you have a metal roof from a different manufacturer?
Visit our "Snow Guard Compatibility by Roof Manufacturer" resource page for detailed information on which snow guards and snow retention systems are compatible with your metal roof.
Compatibility Guidance Note
SnoBlox-Snojax bases the compatibility information presented in this guide on product testing and field experience with North Star Metals metal roof panel profiles. Panel manufacturers periodically update profile specifications, and individual project variables, such as seam condition, coating type, and installation method, can affect outcomes. Customers are encouraged to confirm current panel specifications directly with North Star Metals and to contact SnoBlox-Snojax with project-specific questions before ordering.
Snow Guards for North Star Metals Roofing Panels – Compatibility & Installation FAQ
Yes. North Star Metals Loc Star, Snap Star, and NS-18 standing seam panels support various adhesive-mounted polycarbonate snow guards and compatible non-penetrating clamp-on systems. Product selection depends on seam geometry, available mounting surfaces, and roof conditions. Do not install screw-down snow guards through concealed-fastener standing seam roof panels.
Yes. EcoJax polycarbonate snow guards are compatible with several North Star Metals standing seam and exposed-fastener profiles, including Loc Star, Snap Star, NS-18, Five Star, and En-Dura Star. Proper installation requires a clean, suitable bonding surface and adherence to the manufacturer's adhesive instructions. Avoid curved mounting surfaces and copper roofing, and allow sufficient curing time before the system encounters significant snow loads.
The required number of rows depends on roof slope, eave-to-ridge distance, ground snow load, panel width, and the selected snow retention product. Some roofs require multiple rows to distribute accumulated snow loads across the roof. SnoBlox-Snojax recommends obtaining a project-specific layout with snow guards or rails extending across the required roof areas rather than installing isolated sections above entrances, walkways, or equipment.
SureBond SB-190 adhesive typically requires approximately 28 days to cure at temperatures of 50°F or higher. Temperatures below 50°F can prevent proper curing and compromise adhesive performance. Schedule installations during suitable weather conditions and allow the full curing period before exposing snow guards to significant snow accumulation.






















