null Skip to main content

Economical 6 Foot SnoBar and ColorBar Snow Rail Kits

See Now

Snow Guards for American Building Components ABC

Snow guards for American Building Components metal roofing panels help reduce the risk of sudden snow and ice release above doors, sidewalks, loading areas, vehicles, landscaping, and other vulnerable spaces below the roof edge. The correct SnoBlox-Snojax product depends on whether the roof is a standing-seam concealed-fastener system or an exposed-fastener panel, and on the exact American Building Components panel profile installed.

Compatible American Building Components snow retention options may include adhesive-mounted polycarbonate snow guards, screw-fastened guards, stainless steel SnowCatcher models, PBR-style rails, 2.67 corrugated systems, non-penetrating clamp-on rail systems, and clamp-on SnoCleat products, depending on the panel design.
  • American Building Components' standing-seam and exposed-fastener panels require different snow-guard attachment methods.
  • LokSeam and SL-16 standing seam roofs may accept adhesive-mounted guards and compatible clamp-on rail or cleat systems.
  • Exposed-fastener panels may accept glue-down, screw-down, SnowCatcher, PBR rail, or 2.67 corrugated systems, depending on the profile geometry.
  • Corrugated ABC panels are highly profile-specific because 2-1/2" and 1-1/4" corrugated panels are not the same as standard 2.67" corrugated profiles.
  • Final product selection should always account for roof slope, panel width, snow load, run length, roof material, attachment method, and layout requirements.
Important: Do not choose snow guards based solely on panel appearance. A product that fits one American Building Components profile may be wrong for another. Clamp-on systems are intended only for compatible standing seam profiles, while exposed fastener panels may require adhesive bonding, screw-down attachment, PBR brackets, Tall ColorBrackets, or 2.67 corrugated brackets. Incorrect selection can reduce holding power, create leak risks, or cause premature system failure.

⚡ American Building Components Primary Quick Selection Guide

Use this section for fast profile-level direction. Confirm the exact product fit in the full compatibility charts below.

  • LokSeam and SL-16: Broad standing seam compatibility with adhesive-mounted snow guards, clamp-on SnoBar/ColorBar rail systems, RCB-3 systems, 2 bar rail systems, and SnoCleat RC/RCT.
  • PBR, 7/8 Wide Rib, and Regal Rib: Support some of the widest exposed-fastener product ranges, including selected adhesive/screw-down guards, SnowCatcher options, SnoCleat PBR, and PBR-style rail systems.
  • Imperial Rib, Perma-Clad, Monarch Rib, and Rugged Rib: Compatible with multiple individual guards and PBR-style rail systems, but rib shape and flat width can limit which products should be centered or rib-straddled.
  • PBU and Retro-R: Compatible with selected compact guards and rail options, but the narrower flats require careful product selection and test fitting before ordering a full layout.
  • PBC: Use SnoCleat 2.67, SnoBar 2.67, or ColorBar 2.67. PBR systems do not support standard flat-mounted pad guards.
  • 5V Crimp: Compatible with many individual guards and PBR-style rails, and it is also shown as compatible with SnoCleat 2.67 because of the panel geometry noted in the compatibility chart.
  • Ameri-Drain, 2-1/2 Corrugated, and 1-1/4 Corrugated: The chart shows no compatible SnoBlox-Snojax products for these panels. Contact ABC or order samples to verify before designing a system.

About American Building Components Metal Roofing Systems

American Building Components, commonly referred to as ABC, has supplied metal building products for more than a century. Their product lineup includes metal roofing, siding, light-gauge framing, trim, and accessories for residential, agricultural, commercial, and post-frame construction. Because ABC offers both standing-seam concealed-fastener panels and many exposed-fastener profiles, snow retention compatibility varies by panel type, rib spacing, seam shape, flat width, and fastening method. This guide combines compatibility information for both American Building Components standing-seam and exposed-fastener roof panels to help identify compatible SnoBlox-Snojax snow guards and snow retention systems for specific ABC profiles.

Snow Retention Solutions for American Building Components Metal Roofing

American Building Components manufactures concealed-fastener standing-seam panels and exposed-fastener metal roof panels. Because those roof styles attach differently, the snow retention strategy must match the panel. Standing seam roofs usually benefit from non-penetrating clamp-on systems when the seam shape allows it, while exposed fastener roofs may accept screw-down products when fastened through the proper low flats and into adequate structure.

See our full range of snow guards for metal roofs and use the charts below to confirm which SnoBlox-Snojax products have compatibility with each American Building Components panel. “YES” indicates the product is shown as a fit for that panel. “NO” means it is not shown as compatible for that profile.

Snow Guards for American Building Components Standing Seam Roof Panels

American Building Components standing seam profiles include LokSeam and SL-16. Both profiles are compatible with broad snow retention, including adhesive-mounted polycarbonate snow guards and several clamp-on rail or cleat-style systems. The key distinction is that these concealed-fastener panels should not be treated like screw-down exposed-fastener panels.

Standing seam warning: Screw-down snow guards must not be installed through concealed-fastener standing-seam panels. Use compatible clamp-on products where the seam accepts them, or adhesive-mounted guards where a flat bonding surface is available.

Do you need more information about our compatible snow guards for American Building Components standing-seam roof panels? Check out our full blog here: Snow Guards for American Building Components Standing Seam Roof Panels.

LokSeam and SL-16 are both shown as compatible with adhesive-mounted individual snow guards, SnowBreaker products, clamp-on SnoBar and ColorBar rail systems, RCB-3 systems, 2-bar systems, and SnoCleat RC/RCT options.

LokSeam includes wide panel options and a seam shape that supports multiple snow retention approaches. Minor striations may require a more liberal adhesive bed to help fill small gaps and reduce moisture paths beneath glue-down guards.

SL-16 also offers multiple options, but its wider trapezoidal seam shape may show some visual crimping at clamp attachment points. Ordering sample clamps for a test fit is strongly recommended before placing the main order.

Snow Guards for American Building Components' Exposed Fastener Roof Panels

American Building Components' exposed fastener profiles include PBR, PBU, 5V Crimp, PBC, Retro-R, Imperial Rib, Ameri-Drain, Perma-Clad, 7/8 Wide Rib, Monarch Rib, Regal Rib, Rugged Rib, 2-1/2 Corrugated, and 1-1/4 Corrugated. These panels do not all provide the same flat mounting area, so compatibility changes significantly from one profile to the next.

Exposed fastener reminder: Installers should fasten screw‑down snow guards or rails through the low flats and into the proper structure, except when using products built for corrugated high‑rib mounting, such as the 2.67‑series systems.

Do you need more information about our compatible snow guards for American Building Components' exposed-fastener metal roofing panels? Check out our full blog here: Snow Guards for Exposed Fastener American Building Components Metal Roofing.

ABC Exposed Fastener Compatibility Chart: PBR Through Ameri-Drain Panels

  PBR Panel PBU Panel 5V Crimp Panel PBC Panel Retro-R Panel Imperial Rib Panel Ameri-Drain Panel
IceJax I
IceJax I
YES YES YES NO YES YES NO
IceJax II
IceJax II
YES NO YES NO NO NO NO
EcoJax
EcoJax
YES YES YES NO YES YES NO
SnoBlox Deuce
SnoBlox Deuce
YES YES YES NO YES YES NO
SnoBlox Ace
SnoBlox Ace
YES YES YES NO YES NO NO
SnoJax I
SnoJax I
YES NO YES NO NO YES NO
SnoJax II
SnoJax II
YES NO YES NO NO NO NO
SnowBreaker 3M
SnowBreaker
YES YES YES NO YES YES NO
SnowCatcher
SnowCatcher
YES NO YES NO NO YES NO
Decorative SnowCatcher
Decorative SnowCatcher
YES NO YES NO NO YES NO
SnoCleat PBR
SnoCleat PBR
YES YES YES NO NO YES NO
SnoCleat 2.67
SnoCleat 2.67
NO NO YES YES NO NO NO
SnoBar PBR
SnoBar PBR
YES YES YES NO YES YES NO
ColorBar PBR
ColorBar PBR
YES YES YES NO YES YES NO
SnoBar 2.67
SnoBar 2.67
NO NO NO YES NO NO NO
ColorBar 2.67
ColorBar 2.67
NO NO NO YES NO NO NO

ABC Exposed Fastener Compatibility Chart: Perma-Clad Through Corrugated Panels

  Perma-Clad Panel 7/8 Wide Rib Panel Monarch Rib Panel Regal Rib Panel Rugged Rib Panel 2-1/2 Corrugated Panel 1-1/4 Corrugated Panel
IceJax I
IceJax I
YES YES NO YES NO NO NO
IceJax II
IceJax II
NO YES NO YES NO NO NO
EcoJax
EcoJax
YES YES YES YES YES NO NO
SnoBlox Deuce
SnoBlox Deuce
YES YES YES YES YES NO NO
SnoBlox Ace
SnoBlox Ace
NO YES NO YES NO NO NO
SnoJax I
SnoJax I
YES YES NO YES NO NO NO
SnoJax II
SnoJax II
NO YES NO YES NO NO NO
SnowBreaker 3M
SnowBreaker
YES YES YES YES YES NO NO
SnowCatcher
SnowCatcher
YES YES YES YES YES NO NO
Decorative SnowCatcher
Decorative SnowCatcher
YES YES YES YES YES NO NO
SnoCleat PBR
SnoCleat PBR
YES YES YES YES YES NO NO
SnoCleat 2.67
SnoCleat 2.67
NO NO NO NO NO NO NO
SnoBar PBR
SnoBar PBR
YES YES YES YES YES NO NO
ColorBar PBR
ColorBar PBR
YES YES YES YES YES NO NO
SnoBar 2.67
SnoBar 2.67
NO NO NO NO NO NO NO
ColorBar 2.67
ColorBar 2.67
NO NO NO NO NO NO NO

PBR, 7/8 Wide Rib, and Regal Rib provide some of the broadest exposed-fastener compatibility in the ABC group. These profiles support many individual guards, SnowCatcher options, SnoCleat PBR, SnoBar PBR, and ColorBar PBR systems.

PBU, Retro-R, Monarch Rib, Imperial Rib, Perma-Clad, and Rugged Rib require closer attention to flat width, rib shape, and mounting location. Some products must be centered between ribs, while others may require consistent off-center placement or compact guard styles.

PBC functions as a corrugated-style exception and works with SnoCleat 2.67, SnoBar 2.67, and ColorBar 2.67.

ABC 2-1/2 Corrugated and 1-1/4 Corrugated panels are not shown as compatible because their rib spacing does not match standard 2.67 corrugated snow retention systems.

Ameri-Drain does not have a recommended SnoBlox-Snojax product shown in the chart due to limited profile information and narrow spacing concerns. Contact ABC for profile details and order samples for test fitting before specifying a complete system.

American Building Components Snow Guard Buying Checklist

  • Confirm the exact name of the American Building Components panel before choosing any product.
  • Identify the roof type: standing seam, exposed fastener, PBR-style, R-panel style, or corrugated.
  • Verify the attachment method: adhesive, screw-down, clamp-on, PBR bracket, or 2.67 corrugated bracket.
  • Check ground snow load. Individual glue-down or screw-down guards are generally best suited for lighter snow-load applications. At the same time, higher loads often require rail systems.
  • Request a layout rather than installing only in isolated areas such as doors, chimneys, or HVAC equipment.
  • Order samples or single units when a test fit is needed. SnoBlox-Snojax products and components are available with no minimum order requirement.

Need Help Identifying your ABC Panel?

If you are not sure which ABC panel you have, compare the panel profile carefully, review the two detailed ABC blog posts linked above, and order a single test-fit unit before committing to a full project. For project-specific help, contact SnoBlox-Snojax at support@snojax.com or call 1-800-766-5291.

Do you have a metal roof from a different manufacturer?

Visit our "Snow Guard Compatibility by Roof Manufacturer" resource page for detailed information on which snow guards and snow retention systems are compatible with your metal roof.

Compatibility Guidance Note

The compatibility information presented in this guide is based on SnoBlox-Snojax product testing and field experience with ABC metal roof panel profiles. Panel manufacturers periodically update profile specifications, and individual project variables including seam condition, coating type, and installation method can affect outcomes. Customers are encouraged to confirm current panel specifications directly with ABC and to contact SnoBlox-Snojax with project-specific questions before ordering.

Snow Guards for American Building Components ABC Metal Roofing Panels – Compatibility & Installation FAQ

LokSeam is compatible with adhesive-mounted polycarbonate snow guards, SnowBreaker products, SnoBar and ColorBar standing seam rail systems, RCB-3 rail systems, 2-bar rail systems, and SnoCleat RC/RCT products.
SL-16 is compatible with adhesive-mounted guards, SnowBreaker options, clamp-on SnoBar and ColorBar rail systems, RCB-3 systems, 2-bar rail systems, and SnoCleat RC/RCT products. The wider, trapezoidal seam warrants a sample clamp test‑fit to confirm compatibility.
No. Screw-down snow guards and mechanically fastened rail systems should not be installed through concealed-fastener standing seam panels. Use compatible clamp-on systems or adhesive-mounted guards where the roof surface allows proper bonding.
PBR, 7/8 Wide Rib, and Regal Rib have some of the widest compatibility in the ABC exposed fastener group. Imperial Rib, Perma-Clad, Monarch Rib, and Rugged Rib also support several options. Still, product selection depends more heavily on rib spacing and flat width.
The chart lists PBC as compatible with SnoCleat 2.67, SnoBar 2.67, and ColorBar 2.67. ABC 2-1/2 Corrugated and 1-1/4 Corrugated panels are not shown as compatible with SnoBlox-Snojax systems because their rib spacing differs from standard 2.67 corrugated profiles.
Order samples first before committing to a full project, particularly when working with narrow flats, striations, corrugation, trapezoidal seams, or uncertain mounting surfaces. SnoBlox-Snojax offers individual products and components with no minimum order requirement.