null Skip to main content

Economical 6 Foot SnoBar and ColorBar Snow Rail Kits

See Now

Snow Guards for Western States Metal Roofing

Snow guards for Western States Metal Roofing panels help manage rooftop snow and ice before it can release suddenly above entrances, walkways, parking areas, landscaping, equipment, and other vulnerable locations. The correct SnoBlox-Snojax solution depends first on whether the roof uses a standing-seam concealed-fastener panel or an exposed-fastener profile, and then on the specific panel geometry installed on the building.

Compatible Western States Metal Roofing snow retention options may include adhesive-mounted polycarbonate guards, screw-fastened products, PBR-style rails, 2.67-inch corrugated systems, non-penetrating clamp-on rails, RCB-3 assemblies, 2-bar systems, and panel-specific SnoCleat products.
  • Western States Metal Roofing standing-seam and exposed-fastener panels require different attachment methods.
  • Use compatible clamp-on systems or adhesive-mounted guards on standing-seam panels; do not drive fasteners through concealed-fastener seams.
  • Exposed-fastener profiles may use adhesive, screw-down, PBR-bracket, or 2.67-inch corrugated systems when the panel shape and structure allow them.
  • MS2, Western Lock, Western Seam 1 Inch, and Western Seam 1.5 Inch profiles are broadly compatible with adhesive-mounted and clamp-on products.
  • Final selection must account for panel profile, roof slope, run length, snow load, substrate, coating, striations, and a complete engineered-style layout.
Important: Do not select a snow guard only by appearance. A product that fits one Western States Metal Roofing panel may not fit another. Clamp-on systems only work on compatible standing seams. At the same time, exposed-fastener panels may require low-flat fastening, PBR brackets, 2.67-inch corrugated brackets, or adhesive bonding. The wrong attachment method can reduce holding strength, create leak paths, or cause premature failure.

⚡ Western States Metal Roofing Primary Quick Selection Guide

Use this overview for quick profile-level direction, then confirm each fit in the complete compatibility charts below.

  • MS2, Western Lock, and Western Seam standing-seam panels: Compatible with adhesive-mounted polycarbonate guards, SnoBar/ColorBar standing-seam rails, RCB-3 systems, 2-bar rails, and SnoCleat RC/RCT.
  • 7/8 Inch Corrugated panels: Use compatible 2.67-inch corrugated products, including SnoCleat 2.67, SnoBar 2.67, and ColorBar 2.67.
  • PBR panels: Accept selected polycarbonate guards, SnowCatcher, SnoCleat PBR, SnoBar PBR, and ColorBar PBR.
  • Western Rib panels: Compatible with EcoJax, SnoBlox Deuce, SnowBreaker, SnoBar PBR, and ColorBar PBR as shown below.

About Western States Metal Roofing

Western States Metal Roofing began as a metal-decking distributor in 1996. It expanded into a family-owned manufacturer of metal roofing and siding products. Its product range includes concealed-fastener standing-seam systems, exposed-fastener PBR panels, 7/8-inch corrugated roofing, and the Western Rib profile. Because these panels use different seam and rib geometries, snow retention compatibility must match the exact roof profile.

Snow Retention Solutions for Western States Metal Roofing

Western States Metal Roofing standing-seam and exposed-fastener panels do not share one universal attachment method. Standing-seam roofs generally need non-penetrating clamp-on assemblies when seam geometry permits, or adhesive-mounted polycarbonate guards where the panel pan provides enough bonding area. Exposed-fastener roofs may accept mechanically fastened or adhesive-mounted products when installers follow the panel-specific mounting requirements.

Browse our full selection of snow guards for metal roofs and use the charts below to identify compatible SnoBlox-Snojax products. “YES” indicates a listed fit for that panel. “NO” indicates that the product is not shown as compatible with that profile.

Snow Guards for Western States Metal Roofing Standing Seam Roof Panels

This standing-seam guide covers the MS2 Mechanically Seamed, Western Lock Snap Lock, Western Seam 1 Inch Nailstrip, and Western Seam 1.5 Inch Nailstrip profiles. Although their seam heights and fastening designs differ, all four profiles support the adhesive-mounted polycarbonate guards and compatible clamp-on systems listed below.

Standing seam warning: Never install screw-down snow guards through concealed-fastener standing-seam panels. Use compatible clamp-on products or adhesive-mounted guards with a suitable flat bonding area.

Do you need more information about compatible snow guards for Western States Metal Roofing standing-seam panels? Read our full blog: Snow Guards for Standing Seam Metal Roof Panels by Western States Metal Roofing.

The MS2, Western Lock, Western Seam 1 Inch, and Western Seam 1.5 Inch panels accept a broad range of adhesive-mounted guards and non-penetrating clamp-on snow retention systems.

Striated panels may need additional adhesive to fill minor gaps and limit moisture paths beneath each guard. For rail systems above pedestrian or parking areas, consider IceStopper attachments to help manage snow and ice below the rail.

Snow Guards for Western States Metal Roofing Exposed Fastener Roof Panels

This exposed-fastener guide covers the 7/8 Inch Corrugated, PBR, and Western Rib profiles. Each panel uses different rib spacing and mounting surfaces, so the compatible systems vary substantially by column. The 7/8 Inch Corrugated panel uses 2.67-inch corrugated brackets, the PBR profile accepts many low-flat and PBR-specific options, and Western Rib supports a narrower group of products.

Exposed fastener reminder: When the chart permits screw-down guards or rails, attach them at the approved panel location and into adequate structure. PBR and Western Rib products generally fasten through suitable low flats. At the same time, compatible 2.67-inch systems mount over the raised corrugations as designed.

Do you need more information about compatible snow guards for Western States Metal Roofing exposed-fastener panels? Read our full blog: Snow Guards for Western States Metal Roofing Exposed Fastener Metal Roof Panels.

The 7/8-inch corrugated profile works with the SnoCleat 2.67, SnoBar 2.67, and ColorBar 2.67 systems designed for 2.67-inch corrugated geometry.

The PBR profile supports the broadest exposed-fastener selection, including compatible polycarbonate guards, SnowCatcher, SnoCleat PBR, SnoBar PBR, and ColorBar PBR.

Western Rib works with EcoJax and SnoBlox Deuce, SnowBreaker, SnoBar PBR, and ColorBar PBR. EcoJax mirrors SnoBlox Deuce compatibility as requested.

Western States Metal Roofing Snow Guard Buying Checklist

  • Confirm the exact Western States Metal Roofing panel name before selecting a product.
  • Identify the roof type: standing seam, concealed fastener, exposed fastener, PBR-style, or 2.67-inch corrugated.
  • Verify the attachment method: adhesive, screw-down, clamp-on, PBR bracket, or 2.67-inch corrugated bracket.
  • Check the ground snow load. Individual adhesive or screw-down guards generally suit lighter snow-load applications, while higher loads often require rail systems.
  • Request a layout instead of placing products only above isolated areas such as doors, chimneys, or HVAC equipment.
  • Order samples or single units when you need to confirm fit. SnoBlox-Snojax products and components have no minimum order requirement.

Need Help Identifying Your Western States Metal Roofing Panel?

If you are not sure which Western States Metal Roofing panel you have, carefully compare the panel profile, review the two detailed Western States Metal Roofing blog posts linked above, and order a single test-fit unit before committing to a full project. For project-specific help, contact SnoBlox-Snojax at support@snojax.com or call 1-800-766-5291.

Do you have a metal roof from a different manufacturer?

Visit our "Snow Guard Compatibility by Roof Manufacturer" resource page for detailed information on which snow guards and snow retention systems are compatible with your metal roof.

Compatibility Guidance Note

SnoBlox-Snojax bases the compatibility information presented in this guide on product testing and field experience with Western States Metal Roofing metal roof panel profiles. Panel manufacturers periodically update profile specifications, and individual project variables, such as seam condition, coating type, and installation method, can affect outcomes. Customers are encouraged to confirm current panel specifications directly with Western States Metal Roofing and to contact SnoBlox-Snojax with project-specific questions before ordering.

Snow Guards for Western States Metal Roofing Panels – Compatibility & Installation FAQ

The correct snow guard depends on the specific Western States Metal Roofing panel. Standing seam panels typically use adhesive-mounted polycarbonate snow guards or clamp-on rail systems. In contrast, exposed fastener panels may use adhesive-mounted, screw-fastened, PBR-style, or corrugated-specific products depending on the panel profile.
No. Different Western States Metal Roofing panels have different seam shapes, rib spacing, and attachment methods. Always identify the exact roof panel before selecting snow guards.
No. Standing seam panels should not be penetrated with screw-fastened snow guards. Use compatible clamp-on systems or adhesive-mounted polycarbonate snow guards instead.
The MS2 Mechanically Seamed, Western Lock Snap Lock, Western Seam 1 Inch Nailstrip, and Western Seam 1.5 Inch Nailstrip panels all support compatible clamp-on snow retention systems when the seam geometry matches the attachment.
Depending on the panel profile, compatible options may include SnoBar, ColorBar, RCB-3 rail systems, 2-Bar rail systems, SnoCleat RC, and SnoCleat RCT.
The primary exposed fastener panels covered in this guide include the 7/8 Inch Corrugated, PBR, and Western Rib profiles.
PBR panels are compatible with several products, including selected polycarbonate snow guards, SnowCatcher, SnoCleat PBR, SnoBar PBR, and ColorBar PBR when installed according to project requirements.
The 7/8-inch corrugated profile is compatible with products specifically designed for 2.67-inch corrugated panels, including SnoCleat 2.67, SnoBar 2.67, and ColorBar 2.67.
No. PBR products and corrugated products use different mounting methods and panel geometries. Always choose snow retention systems designed for the specific roof profile.
Yes. Lower snow loads often allow individual snow guards. In comparison, heavier snow loads frequently require engineered rail systems and a complete roof layout.
No. Snow retention systems should be designed for the entire roof. Installing guards only over isolated areas can overload individual products and reduce overall performance.
Yes. Adhesive-mounted polycarbonate snow guards can be installed on many striated panels. However, additional adhesive may be necessary to fill the surface texture and create a proper bond.
Compare your roof profile to the panel photos and dimensions in the Western States Metal Roofing compatibility guides. If you are still unsure, order a sample or contact SnoBlox-Snojax for assistance.
Using a snow guard designed for your exact roof panel helps maximize holding strength, protects the roofing system, reduces the risk of leaks, and provides reliable long-term snow retention.

!