null Skip to main content

Economical 6 Foot SnoBar and ColorBar Snow Rail Kits

See Now

Snow Guards for Everlast Metals

Snow guards for Everlast Metals roofing panels help control the sudden release of rooftop snow and ice above sidewalks, entrances, parking areas, loading zones, landscaping, equipment, and other vulnerable locations. The right SnoBlox-Snojax product depends on whether the Everlast Metals roof uses a standing-seam concealed-fastener system or an exposed-fastener panel, and on the exact panel profile installed on the building.

Compatible Everlast Metals snow retention options may include adhesive-mounted polycarbonate guards, screw-fastened guards, SnowCatcher products, PBR-style rail systems, non-penetrating standing seam rail assemblies, RCB-3 systems, 2-bar systems, and clamp-on SnoCleat products, depending on panel geometry.
  • Everlast Metals standing seam and exposed fastener panels require different attachment methods.
  • Use compatible clamp-on systems or adhesive-mounted guards for standing seam panels, not screw-down attachments through the panels.
  • Exposed fastener panels may accept adhesive-mounted guards, screw-down guards, SnowCatcher, SnoCleat PBR, or PBR-style rail systems, depending on panel shape.
  • ASL-100, ASL-150, DL-100, DL-150, DL-200, and SSL-175 offer broad compatibility with adhesive-mounted guards and clamp-on systems.
  • The NS-100 accepts adhesive-mounted polycarbonate guards but does not accept the clamp-on systems listed in the standing seam chart.
  • Final selection should account for roof slope, panel width, run length, roof material, ground snow load, surface striations, seam configuration, and full-roof layout requirements.
Important: Do not choose snow guards based on appearance alone. A product that works on one Everlast Metals profile may not suit another. Clamp-on systems are intended only for compatible standing seam profiles. Exposed fastener panels may require adhesive bonding, mechanical fastening into suitable structure, or PBR-specific brackets. An incorrect selection can reduce holding strength, increase leak risk, damage the roof, or cause premature system failure.

⚡ Everlast Metals Primary Quick Selection Guide

Use this section for fast panel-level direction. Confirm the exact product fit in the complete compatibility charts below.

  • ASL-100, ASL-150, DL-100, DL-150, DL-200, and SSL-175: Compatible with adhesive-mounted polycarbonate guards, SnoBar and ColorBar standing seam systems, RCB-3 systems, 2-bar systems, and SnoCleat RC/RCT.
  • NS-100: Compatible with the adhesive-mounted polycarbonate guards shown in the chart. Its seam geometry does not accommodate the listed clamp-on products.
  • OMNI Series: Compatible with selected polycarbonate guards, SnowBreaker, SnowCatcher, SnoCleat PBR, SnoBar PBR, and ColorBar PBR.
  • PBR Panel: Compatible with the listed polycarbonate guards, SnowBreaker, SnowCatcher, SnoCleat PBR, SnoBar PBR, and ColorBar PBR.
  • Standing seam warning: Never fasten screw-down snow guards through concealed-fastener standing seam panels.

About Everlast Metals Roofing Systems

Everlast Metals manufactures architectural, commercial, and industrial metal roofing and wall systems. Its roofing lineup includes snap-lock, mechanically seamed, nail-strip, and exposed-fastener profiles in multiple widths, seam heights, gauges, substrates, and finishes. Because these products don't share a universal shape or attachment method, snow guard compatibility must match the exact Everlast Metals panel installed on the building.

Snow Retention Solutions for Everlast Metals Roofing

Standing seam and exposed fastener panels require different snow retention strategies. Compatible standing seam roofs can use non-penetrating clamps that grip the seam without puncturing the panel. Adhesive-mounted polycarbonate guards may also be suitable when the panel pan provides enough flat bonding area. Exposed fastener roofs may accept adhesive-mounted or mechanically fastened products, with screw-down systems secured through the low flats and into adequate supporting structure.

Explore our complete selection of snow guards for metal roofs and use the charts below to compare each Everlast Metals panel with the available SnoBlox-Snojax products. “YES” indicates that the product is shown as a fit for the panel. “NO” means it is not shown as compatible with that profile.

Snow Guards for Everlast Metals Standing Seam Roof Panels

This guide covers the Everlast Metals standing seam profiles ASL-100, ASL-150, DL-100, DL-150, DL-200, NS-100, and SSL-175. These panels differ in seam height, seaming method, panel width, clip design, and surface configuration. All seven profiles may accept the adhesive-mounted polycarbonate products shown below when the panel pan provides a suitable flat bonding surface. The NS-100 differs from the other profiles because its seam shape does not accommodate the listed clamp-on systems.

Standing seam warning: Do not install screw-down snow guards through concealed-fastener standing seam panels. Use compatible clamp-on products where the seam accepts them or adhesive-mounted guards where a suitable flat bonding surface is available.

Do you need more information about compatible snow guards for Everlast Metals standing seam roof panels? Read our full blog: Snow Guards for Everlast Metals Standing Seam Metal Roof Panels.

  ASL-100 ASL-150 DL-100 DL-150 DL-200 NS-100 SSL-175
IceJax I
IceJax I		 YES YES YES YES YES YES YES
IceJax II
IceJax II		 YES YES YES YES YES YES YES
Ecojax
Ecojax		 YES YES YES YES YES YES YES
SnoBlox Deuce
SnoBlox Deuce		 YES YES YES YES YES YES YES
SnoBlox Ace
SnoBlox Ace		 YES YES YES YES YES YES YES
SnoJax II
SnoJax II		 YES YES YES YES YES YES YES
SnowBreaker
SnowBreaker		 YES YES YES YES YES YES YES
SnoBar Standing Seam
SnoBar Standing Seam		 YES YES YES YES YES NO YES
ColorBar Standing Seam
ColorBar Standing Seam		 YES YES YES YES YES NO YES
SnoBar RCB-3
SnoBar RCB-3		 YES YES YES YES YES NO YES
ColorBar RCB-3
ColorBar RCB-3		 YES YES YES YES YES NO YES
2 Bar SnoBar
2 Bar SnoBar		 YES YES YES YES YES NO YES
2 Bar ColorBar
2 Bar ColorBar		 YES YES YES YES YES NO YES
SnoCleat RC
SnoCleat RC		 YES YES YES YES YES NO YES
SnoCleat RCT
SnoCleat RCT		 YES YES YES YES YES NO YES

The ASL-100, ASL-150, DL-100, DL-150, DL-200, and SSL-175 accept a broad range of adhesive-mounted guards and compatible clamp-on systems. We recommend a physical test fit before ordering clamp-on products for an entire project.

The NS-100 accepts the listed adhesive-mounted guards, but its seam shape does not accommodate the clamp-on guards and rail systems in the chart. Aluminum panels may require additional rows of rails because aluminum is less rigid than steel.

Snow Guards for Everlast Metals Exposed Fastener Roof Panels

This guide covers the Everlast Metals OMNI Series and PBR Panel. Both are exposed fastener profiles that provide 36 inches of roof coverage, but their rib arrangements and available flat areas differ. Those differences determine which pad-style snow guards fit correctly and where you can install mechanically fastened products or rail brackets.

Exposed fastener reminder: Install screw-down guards and rail brackets through the panel’s low, flat areas and into adequate supporting structure. Never attach individual guards or rail systems directly to the high ribs.

Do you need more information about compatible snow guards for Everlast Metals exposed fastener roof panels? Read our full blog: Snow Guards for Everlast Metals Exposed Fastener Metal Roof Panels.

  OMNI Series PBR Panel
IceJax I
IceJax I		 YES YES
IceJax II
IceJax II		 NO YES
Ecojax
Ecojax		 YES YES
SnoBlox Deuce
SnoBlox Deuce		 YES YES
SnoBlox Ace
SnoBlox Ace		 NO YES
SnoJax I
SnoJax I		 YES YES
SnoJax II
SnoJax II		 NO YES
SnowBreaker
SnowBreaker		 YES YES
SnowCatcher
SnowCatcher		 YES YES
SnoCleat PBR
SnoCleat PBR		 YES YES
SnoCleat 2.67
SnoCleat 2.67		 NO NO
SnoBar PBR
SnoBar PBR		 YES YES
ColorBar PBR
ColorBar PBR		 YES YES
SnoBar 2.67
SnoBar 2.67		 NO NO
ColorBar 2.67
ColorBar 2.67		 NO NO

The OMNI Series works with products that fit within its available low, flat mounting areas. IceJax II, SnoBlox Ace, and SnoJax II are not shown as compatible because their larger configurations do not fit this panel correctly.

The PBR Panel provides broader pad-style compatibility. IceJax II and SnoJax II should consistently straddle one of the panel’s minor ribs rather than being centered between the ribs. 

Everlast Metals Snow Guard Buying Checklist

  • Confirm the exact Everlast Metals panel name before selecting a product.
  • Identify the roof type: standing seam, concealed fastener, exposed fastener, PBR-style, or corrugated.
  • Verify the attachment method: adhesive-mounted, screw-down, clamp-on, PBR bracket, or 2.67 corrugated bracket.
  • Check the ground snow load. Individual guards are generally better suited to lighter snow-load applications, while higher loads often require rail systems.
  • Request a layout instead of installing snow guards only above isolated areas such as doors, chimneys, walkways, or HVAC equipment.
  • Order a sample or individual component when you need a test fit. SnoBlox-Snojax products and components are available without a minimum-order requirement.

Need Help Identifying Your Everlast Metals Panel?

If you are not sure which Everlast Metals panel you have, carefully compare the panel profile, review the two detailed Everlast Metals blog posts linked above, and order a single test-fit unit before committing to a full project. For project-specific help, contact SnoBlox-Snojax at support@snojax.com or call 1-800-766-5291.

Do you have a metal roof from a different manufacturer?

Visit our "Snow Guard Compatibility by Roof Manufacturer" resource page for detailed information on which snow guards and snow retention systems are compatible with your metal roof.

Compatibility Guidance Note

SnoBlox-Snojax bases the compatibility information presented in this guide on product testing and field experience with Everlast Metals roof panel profiles. Panel manufacturers periodically update profile specifications, and individual project variables, such as seam condition, coating type, and installation method, can affect outcomes. Customers should confirm current panel specifications directly with Everlast Metals and contact SnoBlox-Snojax with project-specific questions before ordering.

A FAQ Page from the SEO Rich Snippets App

Compatibility depends on the exact Everlast Metals panel profile and whether the roof uses concealed or exposed standing-seam fasteners. Adhesive-mounted polycarbonate guards, clamp-on systems, screw-down guards, and rail systems are available for different profiles.
No. Do not penetrate concealed-fastener standing seam panels with screw-down snow guards or rail systems. Use compatible non-penetrating clamp-on products or adhesive-mounted polycarbonate guards where the panel has a suitable flat bonding surface.
These panels are compatible with the listed adhesive-mounted polycarbonate guards and several non-penetrating systems, including SnoBar, ColorBar, RCB-3, 2-bar systems, SnoCleat RC, and SnoCleat RCT. We recommend test-fitting a clamp before ordering a complete system.
The NS-100 is compatible with the adhesive-mounted polycarbonate guards shown in the chart, including IceJax I, IceJax II, Ecojax, SnoBlox Deuce, SnoBlox Ace, SnoJax II, and SnowBreaker. Its seam shape does not accommodate the listed clamp-on guards or rail systems.
Yes. Ecojax fits the same Everlast Metals panel profiles as SnoBlox Deuce. Ecojax is a polycarbonate snow guard that can be adhesive-mounted when the panel material, finish, and available bonding surface are suitable.
The OMNI Series is compatible with IceJax I, Ecojax, SnoBlox Deuce, SnoJax I, SnowBreaker, SnowCatcher, SnoCleat PBR, SnoBar PBR, and ColorBar PBR. IceJax II, SnoBlox Ace, and SnoJax II are not shown as compatible because their larger configurations do not fit the available mounting areas properly.
The PBR Panel is compatible with IceJax I, IceJax II, Ecojax, SnoBlox Deuce, SnoBlox Ace, SnoJax I, SnoJax II, SnowBreaker, SnowCatcher, SnoCleat PBR, SnoBar PBR, and ColorBar PBR.
No. SnoCleat 2.67, SnoBar 2.67, and ColorBar 2.67 are designed for compatible 2.67-inch corrugated panels. They are not compatible with the Everlast Metals OMNI Series or PBR Panel profiles.
Install compatible screw-down snow guards and rail brackets through the panel's low, flat areas and into adequate supporting structure, such as wood decking or purlins. Do not fasten guards or brackets directly to the high ribs.
Not necessarily. The panel must provide enough flat mounting area, and its material and finish must be compatible with SureBond SB-190 adhesive. We do not recommend adhesive-mounted snow guards for copper roofing.
SureBond SB-190 requires about 28 days at 50°F or warmer to fully cure. Plan installation so temperatures stay within the required range throughout curing.
Yes. Seam dimensions, coatings, manufacturing variations, and field conditions can affect compatibility. We recommend ordering one mill-finish SnoCleat or clamp component for a physical test fit before purchasing a complete clamp-on system.
They may. Aluminum is less rigid than steel, so an aluminum roof can require additional rows of rails to distribute the snow load properly. The final design should be based on the panel material, roof dimensions, slope, and local ground snow load.
Individual adhesive-mounted or screw-down guards are generally better suited to areas with ground snow loads of 45 psf or less. More substantial rail systems are typically recommended when the ground snow load exceeds 45 psf.
No. Snow guards should not be concentrated only above isolated areas such as doors, walkways, chimneys, garage entrances, or HVAC equipment. A properly designed system should distribute the retained snow load across the entire roof area and may require multiple rows.

The layout depends on the panel profile and width, roof slope, eave length, roof run, roof material, ground snow load, and selected snow retention system. Request a project-specific layout from SnoBlox-Snojax rather than estimating product quantity and placement.

Several options are available. Polycarbonate guards may be clear or color-molded, while metal guards, brackets, rails, and inserts may be painted or professionally powder-coated. Available options depend on the selected product and project requirements.
Compare the panel's seam or rib shape, coverage width, rib spacing, seam height, and fastening method with Everlast Metals specifications and the panel descriptions in the linked blogs. If you're still unsure, contact SnoBlox-Snojax and consider ordering a single product or clamp for a test fit.

!